Merge tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
 "This is the third and smallest of the SoC specific updates.  Changes
  include:

   - SMP support for the Xilinx zynq platform
   - Smaller imx changes
   - LPAE support for mvebu
   - Moving the orion5x, kirkwood, dove and mvebu platforms to a common
     "mbus" driver for their internal devices.

  It would be good to get feedback on the location of the "mbus" driver.
  Since this is used on multiple platforms may potentially get shared
  with other architectures (powerpc and arm64), it was moved to
  drivers/bus/.  We expect other similar drivers to get moved to the
  same place in order to avoid creating more top-level directories under
  drivers/ or cluttering up the messy drivers/misc/ even more."

* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
  ARM: imx: reset_controller may be disabled
  ARM: mvebu: Align the internal registers virtual base to support LPAE
  ARM: mvebu: Limit the DMA zone when LPAE is selected
  arm: plat-orion: remove addr-map code
  arm: mach-mv78xx0: convert to use the mvebu-mbus driver
  arm: mach-orion5x: convert to use mvebu-mbus driver
  arm: mach-dove: convert to use mvebu-mbus driver
  arm: mach-kirkwood: convert to use mvebu-mbus driver
  arm: mach-mvebu: convert to use mvebu-mbus driver
  ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
  ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
  ARM i.MX53: make tve_ext_sel propagate rate change to PLL
  ARM i.MX53: Remove unused tve_gate clkdev entry
  ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
  ARM: i.MX5: Add PATA and SRTC clocks
  ARM: imx: do not bring up unavailable cores
  ARM: imx: add initial imx6dl support
  ARM: imx1: mm: add call to mxc_device_init
  ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
  ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
  ...

Documentation/devicetree/bindings/clock/imx5-clock.txt

@@ -38,7 +38,6 @@ clocks and IDs.
 	usb_phy_podf		23
 	cpu_podf		24
 	di_pred			25
-	tve_di			26
 	tve_s			27
 	uart1_ipg_gate		28
 	uart1_per_gate		29
@@ -172,6 +171,19 @@ clocks and IDs.
 	can1_serial_gate	157
 	can1_ipg_gate		158
 	owire_gate		159
+	gpu3d_s			160
+	gpu2d_s			161
+	gpu3d_gate		162
+	gpu2d_gate		163
+	garb_gate		164
+	cko1_sel		165
+	cko1_podf		166
+	cko1			167
+	cko2_sel		168
+	cko2_podf		169
+	cko2			170
+	srtc_gate		171
+	pata_gate		172
 
 Examples (for mx53):
 

Documentation/devicetree/bindings/clock/imx6q-clock.txt

@@ -205,6 +205,9 @@ clocks and IDs.
 	enet_ref		190
 	usbphy1_gate		191
 	usbphy2_gate		192
+	pll4_post_div		193
+	pll5_post_div		194
+	pll5_video_div		195
 
 Examples:
 

Documentation/devicetree/bindings/reset/fsl,imx-src.txt

@@ -0,0 +1,49 @@
+Freescale i.MX System Reset Controller
+======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "fsl,<chip>-src"
+- reg: should be register base and length as documented in the
+  datasheet
+- interrupts: Should contain SRC interrupt and CPU WDOG interrupt,
+  in this order.
+- #reset-cells: 1, see below
+
+example:
+
+src: src@020d8000 {
+        compatible = "fsl,imx6q-src";
+        reg = <0x020d8000 0x4000>;
+        interrupts = <0 91 0x04 0 96 0x04>;
+        #reset-cells = <1>;
+};
+
+Specifying reset lines connected to IP modules
+==============================================
+
+The system reset controller can be used to reset the GPU, VPU,
+IPU, and OpenVG IP modules on i.MX5 and i.MX6 ICs. Those device
+nodes should specify the reset line on the SRC in their resets
+property, containing a phandle to the SRC device node and a
+RESET_INDEX specifying which module to reset, as described in
+reset.txt
+
+example:
+
+        ipu1: ipu@02400000 {
+                resets = <&src 2>;
+        };
+        ipu2: ipu@02800000 {
+                resets = <&src 4>;
+        };
+
+The following RESET_INDEX values are valid for i.MX5:
+GPU_RESET     0
+VPU_RESET     1
+IPU1_RESET    2
+OPEN_VG_RESET 3
+The following additional RESET_INDEX value is valid for i.MX6:
+IPU2_RESET    4

Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt

@@ -8,6 +8,8 @@ Required properties:
 - interrupts: Should contain sync interrupt and error interrupt,
   in this order.
 - #crtc-cells: 1, See below
+- resets: phandle pointing to the system reset controller and
+          reset line index, see reset/fsl,imx-src.txt for details
 
 example:
 
@@ -16,6 +18,7 @@ ipu: ipu@18000000 {
 	compatible = "fsl,imx53-ipu";
 	reg = <0x18000000 0x080000000>;
 	interrupts = <11 10>;
+	resets = <&src 2>;
 };
 
 Parallel display support