Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 - new drivers: Kontron PLD, Wondermedia VT
 - mv64xxx driver gained sun4i support and a bigger cleanup
 - duplicate driver 'intel-mid' removed
 - added generic device tree binding for sda holding time (and
   designware driver already uses it)
 - we tried to allow driver probing with only device tree and no i2c
   ids, but I had to revert it because of side effects.  Needs some
   rethinking.
 - driver bugfixes, cleanups...

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
  i2c-designware: use div_u64 to fix link
  i2c: Kontron PLD i2c bus driver
  i2c: iop3xxx: fix build failure after waitqueue changes
  i2c-designware: make SDA hold time configurable
  i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided
  i2c: imx: allow autoloading on dt ids
  i2c: mv64xxx: Fix transfer error code
  i2c: i801: SMBus patch for Intel Coleto Creek DeviceIDs
  i2c: omap: correct usage of the interrupt enable register
  i2c-pxa: prepare clock before use
  Revert "i2c: core: make it possible to match a pure device tree driver"
  i2c: nomadik: allocate adapter number dynamically
  i2c: nomadik: support elder Nomadiks
  i2c: mv64xxx: Add Allwinner sun4i compatible
  i2c: mv64xxx: make the registers offset configurable
  i2c: mv64xxx: Add macros to access parts of registers
  i2c: vt8500: Add support for I2C bus on Wondermedia SoCs
  i2c: designware: fix race between subsequent xfers
  i2c: bfin-twi: Read and write the FIFO in loop
  i2c: core: make it possible to match a pure device tree driver
  ...

Documentation/devicetree/bindings/i2c/i2c-designware.txt

@@ -10,6 +10,10 @@ Recommended properties :
 
  - clock-frequency : desired I2C bus clock frequency in Hz.
 
+Optional properties :
+ - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds.
+   This option is only supported in hardware blocks version 1.11a or newer.
+
 Example :
 
 	i2c@f0000 {
@@ -20,3 +24,14 @@ Example :
 		interrupts = <11>;
 		clock-frequency = <400000>;
 	};
+
+	i2c@1120000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,designware-i2c";
+		reg = <0x1120000 0x1000>;
+		interrupt-parent = <&ictl>;
+		interrupts = <12 1>;
+		clock-frequency = <400000>;
+		i2c-sda-hold-time-ns = <300>;
+	};

Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt

@@ -6,7 +6,11 @@ Required properties :
  - reg             : Offset and length of the register set for the device
  - compatible      : Should be "marvell,mv64xxx-i2c"
  - interrupts      : The interrupt number
- - clock-frequency : Desired I2C bus clock frequency in Hz.
+
+Optional properties :
+
+ - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the
+default frequency is 100kHz
 
 Examples:
 

Documentation/devicetree/bindings/i2c/i2c-vt8500.txt

@@ -0,0 +1,24 @@
+* Wondermedia I2C Controller
+
+Required properties :
+
+ - compatible : should be "wm,wm8505-i2c"
+ - reg : Offset and length of the register set for the device
+ - interrupts : <IRQ> where IRQ is the interrupt number
+ - clocks : phandle to the I2C clock source
+
+Optional properties :
+
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+	Valid values are 100000 and 400000.
+	Default to 100000 if not specified, or invalid value.
+
+Example :
+
+	i2c_0: i2c@d8280000 {
+		compatible = "wm,wm8505-i2c";
+		reg = <0xd8280000 0x1000>;
+		interrupts = <19>;
+		clocks = <&clki2c0>;
+		clock-frequency = <400000>;
+	};

Documentation/i2c/busses/i2c-i801

@@ -24,6 +24,7 @@ Supported adapters:
   * Intel Lynx Point-LP (PCH)
   * Intel Avoton (SOC)
   * Intel Wellsburg (PCH)
+  * Intel Coleto Creek (PCH)
    Datasheets: Publicly available at the Intel website
 
 On Intel Patsburg and later chipsets, both the normal host SMBus controller

MAINTAINERS

@@ -1301,6 +1301,7 @@ S:	Maintained
 F:	arch/arm/mach-vt8500/
 F:	drivers/clocksource/vt8500_timer.c
 F:	drivers/gpio/gpio-vt8500.c
+F:	drivers/i2c/busses/i2c-wmt.c
 F:	drivers/mmc/host/wmt-sdmmc.c
 F:	drivers/pwm/pwm-vt8500.c
 F:	drivers/rtc/rtc-vt8500.c

arch/arc/boot/dts/abilis_tb100_dvk.dts

@@ -45,19 +45,19 @@
 		};
 
 		i2c0: i2c@FF120000 {
-			sda-hold-time = <432>;
+			i2c-sda-hold-time-ns = <432>;
 		};
 		i2c1: i2c@FF121000 {
-			sda-hold-time = <432>;
+			i2c-sda-hold-time-ns = <432>;
 		};
 		i2c2: i2c@FF122000 {
-			sda-hold-time = <432>;
+			i2c-sda-hold-time-ns = <432>;
 		};
 		i2c3: i2c@FF123000 {
-			sda-hold-time = <432>;
+			i2c-sda-hold-time-ns = <432>;
 		};
 		i2c4: i2c@FF124000 {
-			sda-hold-time = <432>;
+			i2c-sda-hold-time-ns = <432>;
 		};
 
 		leds {

arch/arc/boot/dts/abilis_tb101_dvk.dts

@@ -45,19 +45,19 @@
 		};
 
 		i2c0: i2c@FF120000 {
-			sda-hold-time = <432>;
+			i2c-sda-hold-time-ns = <432>;
 		};
 		i2c1: i2c@FF121000 {
-			sda-hold-time = <432>;
+			i2c-sda-hold-time-ns = <432>;
 		};
 		i2c2: i2c@FF122000 {
-			sda-hold-time = <432>;
+			i2c-sda-hold-time-ns = <432>;
 		};
 		i2c3: i2c@FF123000 {
-			sda-hold-time = <432>;
+			i2c-sda-hold-time-ns = <432>;
 		};
 		i2c4: i2c@FF124000 {
-			sda-hold-time = <432>;
+			i2c-sda-hold-time-ns = <432>;
 		};
 
 		leds {

drivers/i2c/busses/Kconfig

@@ -108,6 +108,7 @@ config I2C_I801
 	    Lynx Point-LP (PCH)
 	    Avoton (SOC)
 	    Wellsburg (PCH)
+	    Coleto Creek (PCH)
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-i801.
@@ -475,16 +476,6 @@ config I2C_IMX
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-imx.
 
-config I2C_INTEL_MID
-	tristate "Intel Moorestown/Medfield Platform I2C controller"
-	depends on PCI
-	help
-	  Say Y here if you have an Intel Moorestown/Medfield platform I2C
-	  controller.
-
-	  This support is also available as a module. If so, the module
-	  will be called i2c-intel-mid.
-
 config I2C_IOP3XX
 	tristate "Intel IOPx3xx and IXP4xx on-chip I2C interface"
 	depends on ARCH_IOP32X || ARCH_IOP33X || ARCH_IXP4XX || ARCH_IOP13XX
@@ -495,6 +486,16 @@ config I2C_IOP3XX
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-iop3xx.
 
+config I2C_KEMPLD
+	tristate "Kontron COM I2C Controller"
+	depends on MFD_KEMPLD
+	help
+	  This enables support for the I2C bus interface on some Kontron ETX
+	  and COMexpress (ETXexpress) modules.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called i2c-kempld.
+
 config I2C_MPC
 	tristate "MPC107/824x/85xx/512x/52xx/83xx/86xx"
 	depends on PPC
@@ -508,10 +509,11 @@ config I2C_MPC
 
 config I2C_MV64XXX
 	tristate "Marvell mv64xxx I2C Controller"
-	depends on (MV64X60 || PLAT_ORION)
+	depends on (MV64X60 || PLAT_ORION || ARCH_SUNXI)
 	help
 	  If you say yes to this option, support will be included for the
 	  built-in I2C interface on the Marvell 64xxx line of host bridges.
+	  This driver is also used for Allwinner SoCs I2C controllers.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-mv64xxx.
@@ -725,6 +727,16 @@ config I2C_VERSATILE
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-versatile.
 
+config I2C_WMT
+	tristate "Wondermedia WM8xxx SoC I2C bus support"
+	depends on ARCH_VT8500
+	help
+	  Say yes if you want to support the I2C bus on Wondermedia 8xxx-series
+	  SoCs.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called i2c-wmt.
+
 config I2C_OCTEON
 	tristate "Cavium OCTEON I2C bus support"
 	depends on CPU_CAVIUM_OCTEON

drivers/i2c/busses/Makefile

@@ -46,8 +46,8 @@ obj-$(CONFIG_I2C_GPIO)		+= i2c-gpio.o
 obj-$(CONFIG_I2C_HIGHLANDER)	+= i2c-highlander.o
 obj-$(CONFIG_I2C_IBM_IIC)	+= i2c-ibm_iic.o
 obj-$(CONFIG_I2C_IMX)		+= i2c-imx.o
-obj-$(CONFIG_I2C_INTEL_MID)	+= i2c-intel-mid.o
 obj-$(CONFIG_I2C_IOP3XX)	+= i2c-iop3xx.o
+obj-$(CONFIG_I2C_KEMPLD)	+= i2c-kempld.o
 obj-$(CONFIG_I2C_MPC)		+= i2c-mpc.o
 obj-$(CONFIG_I2C_MV64XXX)	+= i2c-mv64xxx.o
 obj-$(CONFIG_I2C_MXS)		+= i2c-mxs.o
@@ -71,6 +71,7 @@ obj-$(CONFIG_I2C_SIRF)		+= i2c-sirf.o
 obj-$(CONFIG_I2C_STU300)	+= i2c-stu300.o
 obj-$(CONFIG_I2C_TEGRA)		+= i2c-tegra.o
 obj-$(CONFIG_I2C_VERSATILE)	+= i2c-versatile.o
+obj-$(CONFIG_I2C_WMT)		+= i2c-wmt.o
 obj-$(CONFIG_I2C_OCTEON)	+= i2c-octeon.o
 obj-$(CONFIG_I2C_XILINX)	+= i2c-xiic.o
 obj-$(CONFIG_I2C_XLR)		+= i2c-xlr.o

drivers/i2c/busses/i2c-bfin-twi.c

@@ -39,16 +39,11 @@ static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface,
 	unsigned short mast_stat = read_MASTER_STAT(iface);
 
 	if (twi_int_status & XMTSERV) {
-		/* Transmit next data */
-		if (iface->writeNum > 0) {
-			SSYNC();
-			write_XMT_DATA8(iface, *(iface->transPtr++));
-			iface->writeNum--;
-		}
+		if (iface->writeNum <= 0) {
 			/* start receive immediately after complete sending in
 			 * combine mode.
 			 */
-		else if (iface->cur_mode == TWI_I2C_MODE_COMBINED)
+			if (iface->cur_mode == TWI_I2C_MODE_COMBINED)
 				write_MASTER_CTL(iface,
 					read_MASTER_CTL(iface) | MDIR);
 			else if (iface->manual_stop)
@@ -56,16 +51,28 @@ static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface,
 					read_MASTER_CTL(iface) | STOP);
 			else if (iface->cur_mode == TWI_I2C_MODE_REPEAT &&
 				iface->cur_msg + 1 < iface->msg_num) {
-			if (iface->pmsg[iface->cur_msg + 1].flags & I2C_M_RD)
+				if (iface->pmsg[iface->cur_msg + 1].flags &
+					I2C_M_RD)
 					write_MASTER_CTL(iface,
-					read_MASTER_CTL(iface) | MDIR);
+						read_MASTER_CTL(iface) |
+						MDIR);
 				else
 					write_MASTER_CTL(iface,
-					read_MASTER_CTL(iface) & ~MDIR);
+						read_MASTER_CTL(iface) &
+						~MDIR);
+			}
+		}
+		/* Transmit next data */
+		while (iface->writeNum > 0 &&
+			(read_FIFO_STAT(iface) & XMTSTAT) != XMT_FULL) {
+			SSYNC();
+			write_XMT_DATA8(iface, *(iface->transPtr++));
+			iface->writeNum--;
 		}
 	}
 	if (twi_int_status & RCVSERV) {
-		if (iface->readNum > 0) {
+		while (iface->readNum > 0 &&
+			(read_FIFO_STAT(iface) & RCVSTAT)) {
 			/* Receive next data */
 			*(iface->transPtr) = read_RCV_DATA8(iface);
 			if (iface->cur_mode == TWI_I2C_MODE_COMBINED) {

drivers/i2c/busses/i2c-cpm.c

@@ -654,7 +654,7 @@ static int cpm_i2c_probe(struct platform_device *ofdev)
 
 	cpm->ofdev = ofdev;
 
-	dev_set_drvdata(&ofdev->dev, cpm);
+	platform_set_drvdata(ofdev, cpm);
 
 	cpm->adap = cpm_ops;
 	i2c_set_adapdata(&cpm->adap, cpm);
@@ -697,7 +697,7 @@ out_free:
 
 static int cpm_i2c_remove(struct platform_device *ofdev)
 {
-	struct cpm_i2c *cpm = dev_get_drvdata(&ofdev->dev);
+	struct cpm_i2c *cpm = platform_get_drvdata(ofdev);
 
 	i2c_del_adapter(&cpm->adap);
 

drivers/i2c/busses/i2c-davinci.c

@@ -646,13 +646,6 @@ static int davinci_i2c_probe(struct platform_device *pdev)
 	struct resource *mem, *irq;
 	int r;
 
-	/* NOTE: driver uses the static register mapping */
-	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!mem) {
-		dev_err(&pdev->dev, "no mem resource?\n");
-		return -ENODEV;
-	}
-
 	irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	if (!irq) {
 		dev_err(&pdev->dev, "no irq resource?\n");
@@ -697,6 +690,7 @@ static int davinci_i2c_probe(struct platform_device *pdev)
 		return -ENODEV;
 	clk_prepare_enable(dev->clk);
 
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dev->base = devm_ioremap_resource(&pdev->dev, mem);
 	if (IS_ERR(dev->base)) {
 		r = PTR_ERR(dev->base);

drivers/i2c/busses/i2c-designware-core.c

@@ -67,9 +67,12 @@
 #define DW_IC_STATUS		0x70
 #define DW_IC_TXFLR		0x74
 #define DW_IC_RXFLR		0x78
+#define DW_IC_SDA_HOLD		0x7c
 #define DW_IC_TX_ABRT_SOURCE	0x80
 #define DW_IC_ENABLE_STATUS	0x9c
 #define DW_IC_COMP_PARAM_1	0xf4
+#define DW_IC_COMP_VERSION	0xf8
+#define DW_IC_SDA_HOLD_MIN_VERS	0x3131312A
 #define DW_IC_COMP_TYPE		0xfc
 #define DW_IC_COMP_TYPE_VALUE	0x44570140
 
@@ -332,6 +335,16 @@ int i2c_dw_init(struct dw_i2c_dev *dev)
 	dw_writel(dev, lcnt, DW_IC_FS_SCL_LCNT);
 	dev_dbg(dev->dev, "Fast-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt);
 
+	/* Configure SDA Hold Time if required */
+	if (dev->sda_hold_time) {
+		reg = dw_readl(dev, DW_IC_COMP_VERSION);
+		if (reg >= DW_IC_SDA_HOLD_MIN_VERS)
+			dw_writel(dev, dev->sda_hold_time, DW_IC_SDA_HOLD);
+		else
+			dev_warn(dev->dev,
+				"Hardware too old to adjust SDA hold time.");
+	}
+
 	/* Configure Tx/Rx FIFO threshold levels */
 	dw_writel(dev, dev->tx_fifo_depth - 1, DW_IC_TX_TL);
 	dw_writel(dev, 0, DW_IC_RX_TL);
@@ -580,14 +593,23 @@ i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 	i2c_dw_xfer_init(dev);
 
 	/* wait for tx to complete */
-	ret = wait_for_completion_interruptible_timeout(&dev->cmd_complete, HZ);
+	ret = wait_for_completion_timeout(&dev->cmd_complete, HZ);
 	if (ret == 0) {
 		dev_err(dev->dev, "controller timed out\n");
+		/* i2c_dw_init implicitly disables the adapter */
 		i2c_dw_init(dev);
 		ret = -ETIMEDOUT;
 		goto done;
-	} else if (ret < 0)
-		goto done;
+	}
+
+	/*
+	 * We must disable the adapter before unlocking the &dev->lock mutex
+	 * below. Otherwise the hardware might continue generating interrupts
+	 * which in turn causes a race condition with the following transfer.
+	 * Needs some more investigation if the additional interrupts are
+	 * a hardware bug or this driver doesn't handle them correctly yet.
+	 */
+	__i2c_dw_enable(dev, false);
 
 	if (dev->msg_err) {
 		ret = dev->msg_err;
@@ -596,8 +618,6 @@ i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 
 	/* no error */
 	if (likely(!dev->cmd_err)) {
-		/* Disable the adapter */
-		__i2c_dw_enable(dev, false);
 		ret = num;
 		goto done;
 	}

drivers/i2c/busses/i2c-designware-core.h

@@ -90,6 +90,7 @@ struct dw_i2c_dev {
 	unsigned int		tx_fifo_depth;
 	unsigned int		rx_fifo_depth;
 	int			rx_outstanding;
+	u32			sda_hold_time;
 };
 
 #define ACCESS_SWAP		0x00000001

drivers/i2c/busses/i2c-designware-platdrv.c

@@ -34,6 +34,7 @@
 #include <linux/sched.h>
 #include <linux/err.h>
 #include <linux/interrupt.h>
+#include <linux/of.h>
 #include <linux/of_i2c.h>
 #include <linux/platform_device.h>
 #include <linux/pm.h>
@@ -87,13 +88,6 @@ static int dw_i2c_probe(struct platform_device *pdev)
 	struct resource *mem;
 	int irq, r;
 
-	/* NOTE: driver uses the static register mapping */
-	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!mem) {
-		dev_err(&pdev->dev, "no mem resource?\n");
-		return -EINVAL;
-	}
-
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0) {
 		dev_err(&pdev->dev, "no irq resource?\n");
@@ -104,6 +98,7 @@ static int dw_i2c_probe(struct platform_device *pdev)
 	if (!dev)
 		return -ENOMEM;
 
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	dev->base = devm_ioremap_resource(&pdev->dev, mem);
 	if (IS_ERR(dev->base))
 		return PTR_ERR(dev->base);
@@ -121,6 +116,16 @@ static int dw_i2c_probe(struct platform_device *pdev)
 		return PTR_ERR(dev->clk);
 	clk_prepare_enable(dev->clk);
 
+	if (pdev->dev.of_node) {
+		u32 ht = 0;
+		u32 ic_clk = dev->get_clk_rate_khz(dev);
+
+		of_property_read_u32(pdev->dev.of_node,
+					"i2c-sda-hold-time-ns", &ht);
+		dev->sda_hold_time = div_u64((u64)ic_clk * ht + 500000,
+					     1000000);
+	}
+
 	dev->functionality =
 		I2C_FUNC_I2C |
 		I2C_FUNC_10BIT_ADDR |

drivers/i2c/busses/i2c-i801.c

@@ -58,6 +58,7 @@
   Wellsburg (PCH) MS    0x8d7d     32     hard     yes     yes     yes
   Wellsburg (PCH) MS    0x8d7e     32     hard     yes     yes     yes
   Wellsburg (PCH) MS    0x8d7f     32     hard     yes     yes     yes
+  Coleto Creek (PCH)    0x23b0     32     hard     yes     yes     yes
 
   Features supported by this driver:
   Software PEC                     no
@@ -169,6 +170,7 @@
 #define PCI_DEVICE_ID_INTEL_PANTHERPOINT_SMBUS	0x1e22
 #define PCI_DEVICE_ID_INTEL_AVOTON_SMBUS	0x1f3c
 #define PCI_DEVICE_ID_INTEL_DH89XXCC_SMBUS	0x2330
+#define PCI_DEVICE_ID_INTEL_COLETOCREEK_SMBUS	0x23b0
 #define PCI_DEVICE_ID_INTEL_5_3400_SERIES_SMBUS	0x3b30
 #define PCI_DEVICE_ID_INTEL_LYNXPOINT_SMBUS	0x8c22
 #define PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS	0x8d22
@@ -817,6 +819,7 @@ static DEFINE_PCI_DEVICE_TABLE(i801_ids) = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS0) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS1) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS2) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_COLETOCREEK_SMBUS) },
 	{ 0, }
 };
 

drivers/i2c/busses/i2c-ibm_iic.c

@@ -705,7 +705,7 @@ static int iic_probe(struct platform_device *ofdev)
 		return -ENOMEM;
 	}
 
-	dev_set_drvdata(&ofdev->dev, dev);
+	platform_set_drvdata(ofdev, dev);
 
 	dev->vaddr = of_iomap(np, 0);
 	if (dev->vaddr == NULL) {
@@ -782,7 +782,7 @@ error_cleanup:
  */
 static int iic_remove(struct platform_device *ofdev)
 {
-	struct ibm_iic_private *dev = dev_get_drvdata(&ofdev->dev);
+	struct ibm_iic_private *dev = platform_get_drvdata(ofdev);
 
 	i2c_del_adapter(&dev->adap);
 

drivers/i2c/busses/i2c-imx.c

@@ -51,7 +51,6 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/of_i2c.h>
-#include <linux/pinctrl/consumer.h>
 #include <linux/platform_data/i2c-imx.h>
 
 /** Defines ********************************************************************
@@ -148,6 +147,7 @@ static const struct of_device_id i2c_imx_dt_ids[] = {
 	{ .compatible = "fsl,imx21-i2c", .data = &imx_i2c_devtype[IMX21_I2C], },
 	{ /* sentinel */ }
 };
+MODULE_DEVICE_TABLE(of, i2c_imx_dt_ids);
 
 static inline int is_imx1_i2c(struct imx_i2c_struct *i2c_imx)
 {
@@ -493,24 +493,19 @@ static int __init i2c_imx_probe(struct platform_device *pdev)
 	struct imx_i2c_struct *i2c_imx;
 	struct resource *res;
 	struct imxi2c_platform_data *pdata = pdev->dev.platform_data;
-	struct pinctrl *pinctrl;
 	void __iomem *base;
 	int irq, ret;
 	u32 bitrate;
 
 	dev_dbg(&pdev->dev, "<%s>\n", __func__);
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		dev_err(&pdev->dev, "can't get device resources\n");
-		return -ENOENT;
-	}
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0) {
 		dev_err(&pdev->dev, "can't get irq number\n");
 		return -ENOENT;
 	}
 
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	base = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(base))
 		return PTR_ERR(base);
@@ -535,12 +530,6 @@ static int __init i2c_imx_probe(struct platform_device *pdev)
 	i2c_imx->adapter.dev.of_node	= pdev->dev.of_node;
 	i2c_imx->base			= base;
 
-	pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
-	if (IS_ERR(pinctrl)) {
-		dev_err(&pdev->dev, "can't get/select pinctrl\n");
-		return PTR_ERR(pinctrl);
-	}
-
 	/* Get I2C clock */
 	i2c_imx->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(i2c_imx->clk)) {

drivers/i2c/busses/i2c-iop3xx.c

@@ -176,7 +176,7 @@ iop3xx_i2c_wait_event(struct i2c_algo_iop3xx_data *iop3xx_adap,
 		interrupted = wait_event_interruptible_timeout (
 			iop3xx_adap->waitq,
 			(done = compare( sr = iop3xx_i2c_get_srstat(iop3xx_adap) ,flags )),
-			1 * HZ;
+			1 * HZ
 			);
 		if ((rc = iop3xx_i2c_error(sr)) < 0) {
 			*status = sr;