Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (92 commits) gianfar: Revive VLAN support vlan: Export symbols as non GPL symbols. bnx2x: tx_has_work should not wait for FW netxen: reduce memory footprint netxen: fix vlan tso/checksum offload net: Fix linux/if_frad.h's suitability for userspace. net: Move config NET_NS to from net/Kconfig to init/Kconfig isdn: Fix missing ifdef in isdn_ppp networking: document "nc" in addition to "netcat" in netconsole.txt e1000e: workaround hw errata af_key: initialize xfrm encap_oa virtio_net: Fix MAX_PACKET_LEN to support 802.1Q VLANs lcs: fix compilation for !CONFIG_IP_MULTICAST rtl8187: Add termination packet to prevent stall iwlwifi: fix rs_get_rate WARN_ON() p54usb: fix packet loss with first generation devices sctp: Fix another socket race during accept/peeloff sctp: Properly timestamp outgoing data chunks for rtx purposes sctp: Correctly start rtx timer on new packet transmissions. sctp: Fix crc32c calculations on big-endian arhes. ...
2026-05-01 15:00:59 -07:00 · 2009-01-26 15:09:20 -08:00
parent 66673f13c1 cd1f55a5b4
commit 924d26df6b
67 changed files with 815 additions and 478 deletions
@@ -51,7 +51,8 @@ Built-in netconsole starts immediately after the TCP stack is
 initialized and attempts to bring up the supplied dev at the supplied
 address.

-The remote host can run either 'netcat -u -l -p <port>' or syslogd.
+The remote host can run either 'netcat -u -l -p <port>',
+'nc -l -u <port>' or syslogd.

 Dynamic reconfiguration:
 ========================
@@ -431,6 +431,7 @@ set_arg(void __user *b, void *val,int len)
 	return 0;
 }

+#ifdef CONFIG_IPPP_FILTER
 static int get_filter(void __user *arg, struct sock_filter **p)
 {
 	struct sock_fprog uprog;
@@ -465,6 +466,7 @@ static int get_filter(void __user *arg, struct sock_filter **p)
 	*p = code;
 	return uprog.len;
 }
+#endif /* CONFIG_IPPP_FILTER */

 /*
 * ippp device ioctl
@@ -1,6 +1,6 @@
 /* bnx2x.h: Broadcom Everest network driver.
 *
- * Copyright (c) 2007-2008 Broadcom Corporation
+ * Copyright (c) 2007-2009 Broadcom Corporation
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
@@ -271,14 +271,7 @@ struct bnx2x_fastpath {

 #define bnx2x_fp(bp, nr, var)		(bp->fp[nr].var)

-#define BNX2X_HAS_TX_WORK(fp) \
-			((fp->tx_pkt_prod != le16_to_cpu(*fp->tx_cons_sb)) || \
-			 (fp->tx_pkt_prod != fp->tx_pkt_cons))
-
-#define BNX2X_HAS_RX_WORK(fp) \
-			(fp->rx_comp_cons != rx_cons_sb)
-
-#define BNX2X_HAS_WORK(fp)	(BNX2X_HAS_RX_WORK(fp) || BNX2X_HAS_TX_WORK(fp))
+#define BNX2X_HAS_WORK(fp)	(bnx2x_has_rx_work(fp) || bnx2x_has_tx_work(fp))


 /* MC hsi */
@@ -1,4 +1,4 @@
-/* Copyright 2008 Broadcom Corporation
+/* Copyright 2008-2009 Broadcom Corporation
 *
 * Unless you and Broadcom execute a separate written software license
 * agreement governing use of this software, this software is licensed to you
@@ -317,6 +317,9 @@ static u8 bnx2x_emac_enable(struct link_params *params,
 		val &= ~0x810;
 	EMAC_WR(bp, EMAC_REG_EMAC_MODE, val);

+	/* enable emac */
+	REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 1);
+
 	/* enable emac for jumbo packets */
 	EMAC_WR(bp, EMAC_REG_EMAC_RX_MTU_SIZE,
 		(EMAC_RX_MTU_SIZE_JUMBO_ENA |
@@ -1609,7 +1612,7 @@ static u8 bnx2x_link_settings_status(struct link_params *params,
 				      u32 gp_status)
 {
 	struct bnx2x *bp = params->bp;
-
+	u16 new_line_speed;
 	u8 rc = 0;
 	vars->link_status = 0;

@@ -1629,7 +1632,7 @@ static u8 bnx2x_link_settings_status(struct link_params *params,

 		switch (gp_status & GP_STATUS_SPEED_MASK) {
 		case GP_STATUS_10M:
-			vars->line_speed = SPEED_10;
+			new_line_speed = SPEED_10;
 			if (vars->duplex == DUPLEX_FULL)
 				vars->link_status |= LINK_10TFD;
 			else
@@ -1637,7 +1640,7 @@ static u8 bnx2x_link_settings_status(struct link_params *params,
 			break;

 		case GP_STATUS_100M:
-			vars->line_speed = SPEED_100;
+			new_line_speed = SPEED_100;
 			if (vars->duplex == DUPLEX_FULL)
 				vars->link_status |= LINK_100TXFD;
 			else
@@ -1646,7 +1649,7 @@ static u8 bnx2x_link_settings_status(struct link_params *params,

 		case GP_STATUS_1G:
 		case GP_STATUS_1G_KX:
-			vars->line_speed = SPEED_1000;
+			new_line_speed = SPEED_1000;
 			if (vars->duplex == DUPLEX_FULL)
 				vars->link_status |= LINK_1000TFD;
 			else
@@ -1654,7 +1657,7 @@ static u8 bnx2x_link_settings_status(struct link_params *params,
 			break;

 		case GP_STATUS_2_5G:
-			vars->line_speed = SPEED_2500;
+			new_line_speed = SPEED_2500;
 			if (vars->duplex == DUPLEX_FULL)
 				vars->link_status |= LINK_2500TFD;
 			else
@@ -1671,32 +1674,32 @@ static u8 bnx2x_link_settings_status(struct link_params *params,
 		case GP_STATUS_10G_KX4:
 		case GP_STATUS_10G_HIG:
 		case GP_STATUS_10G_CX4:
-			vars->line_speed = SPEED_10000;
+			new_line_speed = SPEED_10000;
 			vars->link_status |= LINK_10GTFD;
 			break;

 		case GP_STATUS_12G_HIG:
-			vars->line_speed = SPEED_12000;
+			new_line_speed = SPEED_12000;
 			vars->link_status |= LINK_12GTFD;
 			break;

 		case GP_STATUS_12_5G:
-			vars->line_speed = SPEED_12500;
+			new_line_speed = SPEED_12500;
 			vars->link_status |= LINK_12_5GTFD;
 			break;

 		case GP_STATUS_13G:
-			vars->line_speed = SPEED_13000;
+			new_line_speed = SPEED_13000;
 			vars->link_status |= LINK_13GTFD;
 			break;

 		case GP_STATUS_15G:
-			vars->line_speed = SPEED_15000;
+			new_line_speed = SPEED_15000;
 			vars->link_status |= LINK_15GTFD;
 			break;

 		case GP_STATUS_16G:
-			vars->line_speed = SPEED_16000;
+			new_line_speed = SPEED_16000;
 			vars->link_status |= LINK_16GTFD;
 			break;

@@ -1708,6 +1711,15 @@ static u8 bnx2x_link_settings_status(struct link_params *params,
 			break;
 		}

+		/* Upon link speed change set the NIG into drain mode.
+		Comes to deals with possible FIFO glitch due to clk change
+		when speed is decreased without link down indicator */
+		if (new_line_speed != vars->line_speed) {
+			REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE
+				    + params->port*4, 0);
+			msleep(1);
+		}
+		vars->line_speed = new_line_speed;
 		vars->link_status |= LINK_STATUS_SERDES_LINK;

 		if ((params->req_line_speed == SPEED_AUTO_NEG) &&
@@ -3571,7 +3583,7 @@ static void bnx2x_set_xgxs_loopback(struct link_params *params,
 			       (MDIO_REG_BANK_CL73_IEEEB0 +
 				(MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)),
 			       0x6041);
-
+		msleep(200);
 		/* set aer mmd back */
 		bnx2x_set_aer_mmd(params, vars);

@@ -3870,9 +3882,15 @@ static u8 bnx2x_link_initialize(struct link_params *params,
 	}

 	if (vars->phy_flags & PHY_XGXS_FLAG) {
-		if (params->req_line_speed &&
+		if ((params->req_line_speed &&
 		    ((params->req_line_speed == SPEED_100) ||
-		     (params->req_line_speed == SPEED_10))) {
+		     (params->req_line_speed == SPEED_10))) ||
+		    (!params->req_line_speed &&
+		     (params->speed_cap_mask >=
+		       PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL) &&
+		     (params->speed_cap_mask <
+		       PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
+		     ))  {
 			vars->phy_flags |= PHY_SGMII_FLAG;
 		} else {
 			vars->phy_flags &= ~PHY_SGMII_FLAG;
@@ -4194,6 +4212,11 @@ static u8 bnx2x_update_link_down(struct link_params *params,
 	/* activate nig drain */
 	REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);

+	/* disable emac */
+	REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
+
+	msleep(10);
+
 	/* reset BigMac */
 	bnx2x_bmac_rx_disable(bp, params->port);
 	REG_WR(bp, GRCBASE_MISC +
@@ -4238,6 +4261,7 @@ static u8 bnx2x_update_link_up(struct link_params *params,

 	/* update shared memory */
 	bnx2x_update_mng(params, vars->link_status);
+	msleep(20);
 	return rc;
 }
 /* This function should called upon link interrupt */
@@ -4276,6 +4300,9 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars)
 	  REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
 	  REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68));

+	/* disable emac */
+	REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
+
 	ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);

 	/* Check external link change only for non-direct */
@@ -4377,10 +4404,11 @@ static u8 bnx2x_8073_common_init_phy(struct bnx2x *bp, u32 shmem_base)
 			      ext_phy_addr[port],
 			      MDIO_PMA_DEVAD,
 			      MDIO_PMA_REG_ROM_VER1, &fw_ver1);
-		if (fw_ver1 == 0) {
+		if (fw_ver1 == 0 || fw_ver1 == 0x4321) {
 			DP(NETIF_MSG_LINK,
-				 "bnx2x_8073_common_init_phy port %x "
-				 "fw Download failed\n", port);
+				 "bnx2x_8073_common_init_phy port %x:"
+				 "Download failed. fw version = 0x%x\n",
+				 port, fw_ver1);
 			return -EINVAL;
 		}

@@ -1,6 +1,6 @@
 /* bnx2x_reg.h: Broadcom Everest network driver.
 *
- * Copyright (c) 2007-2008 Broadcom Corporation
+ * Copyright (c) 2007-2009 Broadcom Corporation
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
@@ -2104,6 +2104,7 @@ static void init_lro_mgr(struct sge_qset *qs, struct net_lro_mgr *lro_mgr)
 {
 	lro_mgr->dev = qs->netdev;
 	lro_mgr->features = LRO_F_NAPI;
+	lro_mgr->frag_align_pad = NET_IP_ALIGN;
 	lro_mgr->ip_summed = CHECKSUM_UNNECESSARY;
 	lro_mgr->ip_summed_aggr = CHECKSUM_UNNECESSARY;
 	lro_mgr->max_desc = T3_MAX_LRO_SES;
@@ -981,11 +981,15 @@ static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw)
 		ew32(PBA_ECC, reg);
 	}

-	/* PCI-Ex Control Register */
+	/* PCI-Ex Control Registers */
 	if (hw->mac.type == e1000_82574) {
 		reg = er32(GCR);
 		reg |= (1 << 22);
 		ew32(GCR, reg);
+
+		reg = er32(GCR2);
+		reg |= 1;
+		ew32(GCR2, reg);
 	}

 	return;
@@ -206,6 +206,7 @@ enum e1e_registers {
 	E1000_MANC2H    = 0x05860, /* Management Control To Host - RW */
 	E1000_SW_FW_SYNC = 0x05B5C, /* Software-Firmware Synchronization - RW */
 	E1000_GCR	= 0x05B00, /* PCI-Ex Control */
+	E1000_GCR2      = 0x05B64, /* PCI-Ex Control #2 */
 	E1000_FACTPS    = 0x05B30, /* Function Active and Power State to MNG */
 	E1000_SWSM      = 0x05B50, /* SW Semaphore */
 	E1000_FWSM      = 0x05B54, /* FW Semaphore */
@@ -1423,15 +1423,11 @@ static void gfar_vlan_rx_register(struct net_device *dev,
 {
 	struct gfar_private *priv = netdev_priv(dev);
 	unsigned long flags;
-	struct vlan_group *old_grp;
 	u32 tempval;

 	spin_lock_irqsave(&priv->rxlock, flags);

-	old_grp = priv->vlgrp;
-
-	if (old_grp == grp)
-		return;
+	priv->vlgrp = grp;

 	if (grp) {
 		/* Enable VLAN tag insertion */
@@ -318,6 +318,9 @@ static void ixgbe_update_rx_dca(struct ixgbe_adapter *adapter,
 		rxctrl |= dca3_get_tag(&adapter->pdev->dev, cpu);
 		rxctrl |= IXGBE_DCA_RXCTRL_DESC_DCA_EN;
 		rxctrl |= IXGBE_DCA_RXCTRL_HEAD_DCA_EN;
+		rxctrl &= ~(IXGBE_DCA_RXCTRL_DESC_RRO_EN);
+		rxctrl &= ~(IXGBE_DCA_RXCTRL_DESC_WRO_EN |
+			    IXGBE_DCA_RXCTRL_DESC_HSRO_EN);
 		IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_RXCTRL(q), rxctrl);
 		rx_ring->cpu = cpu;
 	}
@@ -1741,38 +1744,6 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 	IXGBE_WRITE_REG(hw, IXGBE_RXCSUM, rxcsum);
 }

-static void ixgbe_vlan_rx_register(struct net_device *netdev,
-                                   struct vlan_group *grp)
-{
-	struct ixgbe_adapter *adapter = netdev_priv(netdev);
-	u32 ctrl;
-
-	if (!test_bit(__IXGBE_DOWN, &adapter->state))
-		ixgbe_irq_disable(adapter);
-	adapter->vlgrp = grp;
-
-	/*
-	 * For a DCB driver, always enable VLAN tag stripping so we can
-	 * still receive traffic from a DCB-enabled host even if we're
-	 * not in DCB mode.
-	 */
-	ctrl = IXGBE_READ_REG(&adapter->hw, IXGBE_VLNCTRL);
-	ctrl |= IXGBE_VLNCTRL_VME;
-	ctrl &= ~IXGBE_VLNCTRL_CFIEN;
-	IXGBE_WRITE_REG(&adapter->hw, IXGBE_VLNCTRL, ctrl);
-
-	if (grp) {
-		/* enable VLAN tag insert/strip */
-		ctrl = IXGBE_READ_REG(&adapter->hw, IXGBE_VLNCTRL);
-		ctrl |= IXGBE_VLNCTRL_VME;
-		ctrl &= ~IXGBE_VLNCTRL_CFIEN;
-		IXGBE_WRITE_REG(&adapter->hw, IXGBE_VLNCTRL, ctrl);
-	}
-
-	if (!test_bit(__IXGBE_DOWN, &adapter->state))
-		ixgbe_irq_enable(adapter);
-}
-
 static void ixgbe_vlan_rx_add_vid(struct net_device *netdev, u16 vid)
 {
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
@@ -1799,6 +1770,39 @@ static void ixgbe_vlan_rx_kill_vid(struct net_device *netdev, u16 vid)
 	hw->mac.ops.set_vfta(&adapter->hw, vid, 0, false);
 }

+static void ixgbe_vlan_rx_register(struct net_device *netdev,
+                                   struct vlan_group *grp)
+{
+	struct ixgbe_adapter *adapter = netdev_priv(netdev);
+	u32 ctrl;
+
+	if (!test_bit(__IXGBE_DOWN, &adapter->state))
+		ixgbe_irq_disable(adapter);
+	adapter->vlgrp = grp;
+
+	/*
+	 * For a DCB driver, always enable VLAN tag stripping so we can
+	 * still receive traffic from a DCB-enabled host even if we're
+	 * not in DCB mode.
+	 */
+	ctrl = IXGBE_READ_REG(&adapter->hw, IXGBE_VLNCTRL);
+	ctrl |= IXGBE_VLNCTRL_VME;
+	ctrl &= ~IXGBE_VLNCTRL_CFIEN;
+	IXGBE_WRITE_REG(&adapter->hw, IXGBE_VLNCTRL, ctrl);
+	ixgbe_vlan_rx_add_vid(netdev, 0);
+
+	if (grp) {
+		/* enable VLAN tag insert/strip */
+		ctrl = IXGBE_READ_REG(&adapter->hw, IXGBE_VLNCTRL);
+		ctrl |= IXGBE_VLNCTRL_VME;
+		ctrl &= ~IXGBE_VLNCTRL_CFIEN;
+		IXGBE_WRITE_REG(&adapter->hw, IXGBE_VLNCTRL, ctrl);
+	}
+
+	if (!test_bit(__IXGBE_DOWN, &adapter->state))
+		ixgbe_irq_enable(adapter);
+}
+
 static void ixgbe_restore_vlan(struct ixgbe_adapter *adapter)
 {
 	ixgbe_vlan_rx_register(adapter->netdev, adapter->vlgrp);
@@ -2074,6 +2078,9 @@ static int ixgbe_up_complete(struct ixgbe_adapter *adapter)

 	ixgbe_irq_enable(adapter);

+	/* enable transmits */
+	netif_tx_start_all_queues(netdev);
+
 	/* bring the link up in the watchdog, this could race with our first
 	 * link up interrupt but shouldn't be a problem */
 	adapter->flags |= IXGBE_FLAG_NEED_LINK_UPDATE;
@@ -3475,7 +3482,6 @@ static void ixgbe_watchdog_task(struct work_struct *work)
 			        (FLOW_TX ? "TX" : "None"))));

 			netif_carrier_on(netdev);
-			netif_tx_wake_all_queues(netdev);
 		} else {
 			/* Force detection of hung controller */
 			adapter->detect_tx_hung = true;
@@ -3487,7 +3493,6 @@ static void ixgbe_watchdog_task(struct work_struct *work)
 			printk(KERN_INFO "ixgbe: %s NIC Link is Down\n",
 			       netdev->name);
 			netif_carrier_off(netdev);
-			netif_tx_stop_all_queues(netdev);
 		}
 	}

@@ -4218,7 +4223,6 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
 	}

 	netif_carrier_off(netdev);
-	netif_tx_stop_all_queues(netdev);

 	strcpy(netdev->name, "eth%d");
 	err = register_netdev(netdev);
@@ -404,6 +404,9 @@
 #define IXGBE_DCA_RXCTRL_DESC_DCA_EN (1 << 5) /* DCA Rx Desc enable */
 #define IXGBE_DCA_RXCTRL_HEAD_DCA_EN (1 << 6) /* DCA Rx Desc header enable */
 #define IXGBE_DCA_RXCTRL_DATA_DCA_EN (1 << 7) /* DCA Rx Desc payload enable */
+#define IXGBE_DCA_RXCTRL_DESC_RRO_EN (1 << 9) /* DCA Rx rd Desc Relax Order */
+#define IXGBE_DCA_RXCTRL_DESC_WRO_EN (1 << 13) /* DCA Rx wr Desc Relax Order */
+#define IXGBE_DCA_RXCTRL_DESC_HSRO_EN (1 << 15) /* DCA Rx Split Header RO */

 #define IXGBE_DCA_TXCTRL_CPUID_MASK 0x0000001F /* Tx CPUID Mask */
 #define IXGBE_DCA_TXCTRL_DESC_DCA_EN (1 << 5) /* DCA Tx Desc enable */
@@ -416,6 +416,9 @@ static int korina_rx(struct net_device *dev, int limit)
 			if (devcs & ETH_RX_MP)
 				dev->stats.multicast++;

+			/* 16 bit align */
+			skb_reserve(skb_new, 2);
+
 			lp->rx_skb[lp->rx_next_done] = skb_new;
 		}

@@ -740,6 +743,7 @@ static struct ethtool_ops netdev_ethtool_ops = {
 static void korina_alloc_ring(struct net_device *dev)
 {
 	struct korina_private *lp = netdev_priv(dev);
+	struct sk_buff *skb;
 	int i;

 	/* Initialize the transmit descriptors */
@@ -755,8 +759,6 @@ static void korina_alloc_ring(struct net_device *dev)

 	/* Initialize the receive descriptors */
 	for (i = 0; i < KORINA_NUM_RDS; i++) {
-		struct sk_buff *skb = lp->rx_skb[i];
-
 		skb = dev_alloc_skb(KORINA_RBSIZE + 2);
 		if (!skb)
 			break;
@@ -769,11 +771,12 @@ static void korina_alloc_ring(struct net_device *dev)
 		lp->rd_ring[i].link = CPHYSADDR(&lp->rd_ring[i+1]);
 	}

-	/* loop back */
-	lp->rd_ring[i].link = CPHYSADDR(&lp->rd_ring[0]);
-	lp->rx_next_done  = 0;
+	/* loop back receive descriptors, so the last
+	 * descriptor points to the first one */
+	lp->rd_ring[i - 1].link = CPHYSADDR(&lp->rd_ring[0]);
+	lp->rd_ring[i - 1].control |= DMA_DESC_COD;

-	lp->rd_ring[i].control |= DMA_DESC_COD;
+	lp->rx_next_done  = 0;
 	lp->rx_chain_head = 0;
 	lp->rx_chain_tail = 0;
 	lp->rx_chain_status = desc_empty;
@@ -321,6 +321,10 @@ static void macb_tx(struct macb *bp)
 		printk(KERN_ERR "%s: TX underrun, resetting buffers\n",
 			bp->dev->name);

+		/* Transfer ongoing, disable transmitter, to avoid confusion */
+		if (status & MACB_BIT(TGO))
+			macb_writel(bp, NCR, macb_readl(bp, NCR) & ~MACB_BIT(TE));
+
 		head = bp->tx_head;

 		/*Mark all the buffer as used to avoid sending a lost buffer*/
@@ -343,6 +347,10 @@ static void macb_tx(struct macb *bp)
 		}

 		bp->tx_head = bp->tx_tail = 0;
+
+		/* Enable the transmitter again */
+		if (status & MACB_BIT(TGO))
+			macb_writel(bp, NCR, macb_readl(bp, NCR) | MACB_BIT(TE));
 	}

 	if (!(status & MACB_BIT(COMP)))
@@ -136,21 +136,23 @@ static char mv643xx_eth_driver_version[] = "1.4";
 /*
 * SDMA configuration register.
 */
+#define RX_BURST_SIZE_4_64BIT		(2 << 1)
 #define RX_BURST_SIZE_16_64BIT		(4 << 1)
 #define BLM_RX_NO_SWAP			(1 << 4)
 #define BLM_TX_NO_SWAP			(1 << 5)
+#define TX_BURST_SIZE_4_64BIT		(2 << 22)
 #define TX_BURST_SIZE_16_64BIT		(4 << 22)

 #if defined(__BIG_ENDIAN)
 #define PORT_SDMA_CONFIG_DEFAULT_VALUE		\
-		(RX_BURST_SIZE_16_64BIT	|	\
-		TX_BURST_SIZE_16_64BIT)
+		(RX_BURST_SIZE_4_64BIT	|	\
+		 TX_BURST_SIZE_4_64BIT)
 #elif defined(__LITTLE_ENDIAN)
 #define PORT_SDMA_CONFIG_DEFAULT_VALUE		\
-		(RX_BURST_SIZE_16_64BIT	|	\
+		(RX_BURST_SIZE_4_64BIT	|	\
 		 BLM_RX_NO_SWAP		|	\
 		 BLM_TX_NO_SWAP		|	\
-		TX_BURST_SIZE_16_64BIT)
+		 TX_BURST_SIZE_4_64BIT)
 #else
 #error One of __BIG_ENDIAN or __LITTLE_ENDIAN must be defined
 #endif
@@ -1594,7 +1596,7 @@ oom:
 			entry = addr_crc(a);
 		}

-		table[entry >> 2] |= 1 << (entry & 3);
+		table[entry >> 2] |= 1 << (8 * (entry & 3));
 	}

 	for (i = 0; i < 0x100; i += 4) {
@@ -2210,6 +2212,7 @@ static int mv643xx_eth_stop(struct net_device *dev)
 	struct mv643xx_eth_private *mp = netdev_priv(dev);
 	int i;

+	wrlp(mp, INT_MASK_EXT, 0x00000000);
 	wrlp(mp, INT_MASK, 0x00000000);
 	rdlp(mp, INT_MASK);

@@ -1,7 +1,7 @@
 /*************************************************************************
 * myri10ge.c: Myricom Myri-10G Ethernet driver.
 *
- * Copyright (C) 2005 - 2007 Myricom, Inc.
+ * Copyright (C) 2005 - 2009 Myricom, Inc.
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
@@ -75,7 +75,7 @@
 #include "myri10ge_mcp.h"
 #include "myri10ge_mcp_gen_header.h"

-#define MYRI10GE_VERSION_STR "1.4.4-1.398"
+#define MYRI10GE_VERSION_STR "1.4.4-1.401"

 MODULE_DESCRIPTION("Myricom 10G driver (10GbE)");
 MODULE_AUTHOR("Maintainer: help@myri.com");
@@ -3786,7 +3786,7 @@ static int myri10ge_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	if (status != 0) {
 		dev_err(&pdev->dev, "Error %d writing PCI_EXP_DEVCTL\n",
 			status);
-		goto abort_with_netdev;
+		goto abort_with_enabled;
 	}

 	pci_set_master(pdev);
@@ -3801,13 +3801,13 @@ static int myri10ge_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	}
 	if (status != 0) {
 		dev_err(&pdev->dev, "Error %d setting DMA mask\n", status);
-		goto abort_with_netdev;
+		goto abort_with_enabled;
 	}
 	(void)pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
 	mgp->cmd = dma_alloc_coherent(&pdev->dev, sizeof(*mgp->cmd),
 				      &mgp->cmd_bus, GFP_KERNEL);
 	if (mgp->cmd == NULL)
-		goto abort_with_netdev;
+		goto abort_with_enabled;

 	mgp->board_span = pci_resource_len(pdev, 0);
 	mgp->iomem_base = pci_resource_start(pdev, 0);
@@ -3943,8 +3943,10 @@ abort_with_mtrr:
 	dma_free_coherent(&pdev->dev, sizeof(*mgp->cmd),
 			  mgp->cmd, mgp->cmd_bus);

-abort_with_netdev:
+abort_with_enabled:
+	pci_disable_device(pdev);

+abort_with_netdev:
 	free_netdev(netdev);
 	return status;
 }
@@ -3990,6 +3992,7 @@ static void myri10ge_remove(struct pci_dev *pdev)
 			  mgp->cmd, mgp->cmd_bus);

 	free_netdev(netdev);
+	pci_disable_device(pdev);
 	pci_set_drvdata(pdev, NULL);
 }

@@ -146,7 +146,7 @@

 #define MAX_RX_BUFFER_LENGTH		1760
 #define MAX_RX_JUMBO_BUFFER_LENGTH 	8062
-#define MAX_RX_LRO_BUFFER_LENGTH	((48*1024)-512)
+#define MAX_RX_LRO_BUFFER_LENGTH	(8062)
 #define RX_DMA_MAP_LEN			(MAX_RX_BUFFER_LENGTH - 2)
 #define RX_JUMBO_DMA_MAP_LEN	\
 	(MAX_RX_JUMBO_BUFFER_LENGTH - 2)
@@ -207,11 +207,11 @@

 #define MAX_CMD_DESCRIPTORS		4096
 #define MAX_RCV_DESCRIPTORS		16384
-#define MAX_CMD_DESCRIPTORS_HOST	(MAX_CMD_DESCRIPTORS / 4)
-#define MAX_RCV_DESCRIPTORS_1G		(MAX_RCV_DESCRIPTORS / 4)
-#define MAX_RCV_DESCRIPTORS_10G		8192
-#define MAX_JUMBO_RCV_DESCRIPTORS	1024
-#define MAX_LRO_RCV_DESCRIPTORS		64
+#define MAX_CMD_DESCRIPTORS_HOST	1024
+#define MAX_RCV_DESCRIPTORS_1G		2048
+#define MAX_RCV_DESCRIPTORS_10G		4096
+#define MAX_JUMBO_RCV_DESCRIPTORS	512
+#define MAX_LRO_RCV_DESCRIPTORS		8
 #define MAX_RCVSTATUS_DESCRIPTORS	MAX_RCV_DESCRIPTORS
 #define MAX_JUMBO_RCV_DESC	MAX_JUMBO_RCV_DESCRIPTORS
 #define MAX_RCV_DESC		MAX_RCV_DESCRIPTORS
@@ -561,7 +561,10 @@ netxen_nic_get_ringparam(struct net_device *dev, struct ethtool_ringparam *ring)
 	}
 	ring->tx_pending = adapter->max_tx_desc_count;

-	ring->rx_max_pending = MAX_RCV_DESCRIPTORS;
+	if (adapter->ahw.board_type == NETXEN_NIC_GBE)
+		ring->rx_max_pending = MAX_RCV_DESCRIPTORS_1G;
+	else
+		ring->rx_max_pending = MAX_RCV_DESCRIPTORS_10G;
 	ring->tx_max_pending = MAX_CMD_DESCRIPTORS_HOST;
 	ring->rx_jumbo_max_pending = MAX_JUMBO_RCV_DESCRIPTORS;
 	ring->rx_mini_max_pending = 0;
@@ -735,17 +735,18 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent)

 	SET_ETHTOOL_OPS(netdev, &netxen_nic_ethtool_ops);

-	/* ScatterGather support */
-	netdev->features = NETIF_F_SG;
-	netdev->features |= NETIF_F_IP_CSUM;
-	netdev->features |= NETIF_F_TSO;
+	netdev->features |= (NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO);
+	netdev->vlan_features |= (NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO);
+
 	if (NX_IS_REVISION_P3(revision_id)) {
-		netdev->features |= NETIF_F_IPV6_CSUM;
-		netdev->features |= NETIF_F_TSO6;
+		netdev->features |= (NETIF_F_IPV6_CSUM | NETIF_F_TSO6);
+		netdev->vlan_features |= (NETIF_F_IPV6_CSUM | NETIF_F_TSO6);
 	}

-	if (adapter->pci_using_dac)
+	if (adapter->pci_using_dac) {
 		netdev->features |= NETIF_F_HIGHDMA;
+		netdev->vlan_features |= NETIF_F_HIGHDMA;
+	}

 	/*
 	 * Set the CRB window to invalid. If any register in window 0 is
@@ -1166,6 +1167,14 @@ static bool netxen_tso_check(struct net_device *netdev,
 {
 	bool tso = false;
 	u8 opcode = TX_ETHER_PKT;
+	__be16 protocol = skb->protocol;
+	u16 flags = 0;
+
+	if (protocol == __constant_htons(ETH_P_8021Q)) {
+		struct vlan_ethhdr *vh = (struct vlan_ethhdr *)skb->data;
+		protocol = vh->h_vlan_encapsulated_proto;
+		flags = FLAGS_VLAN_TAGGED;
+	}

 	if ((netdev->features & (NETIF_F_TSO | NETIF_F_TSO6)) &&
 			skb_shinfo(skb)->gso_size > 0) {
@@ -1174,21 +1183,21 @@ static bool netxen_tso_check(struct net_device *netdev,
 		desc->total_hdr_length =
 			skb_transport_offset(skb) + tcp_hdrlen(skb);

-		opcode = (skb->protocol == htons(ETH_P_IPV6)) ?
+		opcode = (protocol == __constant_htons(ETH_P_IPV6)) ?
 				TX_TCP_LSO6 : TX_TCP_LSO;
 		tso = true;

 	} else if (skb->ip_summed == CHECKSUM_PARTIAL) {
 		u8 l4proto;

-		if (skb->protocol == htons(ETH_P_IP)) {
+		if (protocol == __constant_htons(ETH_P_IP)) {
 			l4proto = ip_hdr(skb)->protocol;

 			if (l4proto == IPPROTO_TCP)
 				opcode = TX_TCP_PKT;
 			else if(l4proto == IPPROTO_UDP)
 				opcode = TX_UDP_PKT;
-		} else if (skb->protocol == htons(ETH_P_IPV6)) {
+		} else if (protocol == __constant_htons(ETH_P_IPV6)) {
 			l4proto = ipv6_hdr(skb)->nexthdr;

 			if (l4proto == IPPROTO_TCP)
@@ -1199,7 +1208,7 @@ static bool netxen_tso_check(struct net_device *netdev,
 	}
 	desc->tcp_hdr_offset = skb_transport_offset(skb);
 	desc->ip_hdr_offset = skb_network_offset(skb);
-	netxen_set_tx_flags_opcode(desc, 0, opcode);
+	netxen_set_tx_flags_opcode(desc, flags, opcode);
 	return tso;
 }

@@ -296,8 +296,7 @@ static int mdio_bus_suspend(struct device * dev, pm_message_t state)
 	struct phy_driver *phydrv = to_phy_driver(drv);
 	struct phy_device *phydev = to_phy_device(dev);

-	if ((!device_may_wakeup(phydev->dev.parent)) &&
-		(phydrv && phydrv->suspend))
+	if (drv && phydrv->suspend && !device_may_wakeup(phydev->dev.parent))
 		ret = phydrv->suspend(phydev);

 	return ret;
@@ -310,8 +309,7 @@ static int mdio_bus_resume(struct device * dev)
 	struct phy_driver *phydrv = to_phy_driver(drv);
 	struct phy_device *phydev = to_phy_device(dev);

-	if ((!device_may_wakeup(phydev->dev.parent)) &&
-		(phydrv && phydrv->resume))
+	if (drv && phydrv->resume && !device_may_wakeup(phydev->dev.parent))
 		ret = phydrv->resume(phydev);

 	return ret;
--- a/Show More
+++ b/Show More