Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (171 commits)
  Blackfin arch: fix bug - BF527 0.2 silicon has different CPUID (DSPID) value
  Blackfin arch: Enlarge flash partition for kenel for bf533/bf537 boards
  Blackfin arch: fix bug: kernel crash when enable SDIO host driver
  Blackfin arch: Print FP at level KERN_NOTICE
  Blackfin arch: drop ad73311 test code
  Blackfin arch: update board default configs
  Blackfin arch: Set PB4 as the default irq for bf548 board v1.4+.
  Blackfin arch: fix typo in early printk bit size processing
  Blackfin arch: enable reprogram cclk and sclk for bf518f-ezbrd
  Blackfin arch: add SDIO host driver platform data
  Blackfin arch: fix bug - kernel stops at initial console
  Blackfin arch: fix bug - kernel crash after config IP for ethernet port
  Blackfin arch: add sdh support for bf518f-ezbrd
  Blackfin arch: fix bug - kernel detects BF532 incorrectly
  Blackfin arch: add () to avoid warnings from gcc
  Blackfin arch: change HWTRACE Kconfig and set it on default
  Blackfin arch: Clean oprofile build path for blackfin
  Blackfin arch: remove hardware PM code, oprofile not use it
  Blackfin arch: rewrite get_sclk()/get_vco()
  Blackfin arch: cleanup and unify the ins functions
  ...

Documentation/blackfin/00-INDEX

@@ -9,3 +9,6 @@ cachefeatures.txt
 
 Filesystems
 	- Requirements for mounting the root file system.
+
+bfin-gpio-note.txt
+	- Notes in developing/using bfin-gpio driver.

Documentation/blackfin/bfin-gpio-notes.txt

@@ -0,0 +1,71 @@
+/*
+ * File:         Documentation/blackfin/bfin-gpio-note.txt
+ * Based on:
+ * Author:
+ *
+ * Created:      $Id: bfin-gpio-note.txt 2008-11-24 16:42 grafyang $
+ * Description:  This file contains the notes in developing/using bfin-gpio.
+ *
+ *
+ * Rev:
+ *
+ * Modified:
+ *               Copyright 2004-2008 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ */
+
+
+1. Blackfin GPIO introduction
+
+    There are many GPIO pins on Blackfin. Most of these pins are muxed to
+    multi-functions. They can be configured as peripheral, or just as GPIO,
+    configured to input with interrupt enabled, or output.
+
+    For detailed information, please see "arch/blackfin/kernel/bfin_gpio.c",
+    or the relevant HRM.
+
+
+2. Avoiding resource conflict
+
+    Followed function groups are used to avoiding resource conflict,
+    - Use the pin as peripheral,
+	int peripheral_request(unsigned short per, const char *label);
+	int peripheral_request_list(const unsigned short per[], const char *label);
+	void peripheral_free(unsigned short per);
+	void peripheral_free_list(const unsigned short per[]);
+    - Use the pin as GPIO,
+	int bfin_gpio_request(unsigned gpio, const char *label);
+	void bfin_gpio_free(unsigned gpio);
+    - Use the pin as GPIO interrupt,
+	int bfin_gpio_irq_request(unsigned gpio, const char *label);
+	void bfin_gpio_irq_free(unsigned gpio);
+
+    The request functions will record the function state for a certain pin,
+    the free functions will clear it's function state.
+    Once a pin is requested, it can't be requested again before it is freed by
+    previous caller, otherwise kernel will dump stacks, and the request
+    function fail.
+    These functions are wrapped by other functions, most of the users need not
+    care.
+
+
+3. But there are some exceptions
+    - Kernel permit the identical GPIO be requested both as GPIO and GPIO
+    interrut.
+    Some drivers, like gpio-keys, need this behavior. Kernel only print out
+    warning messages like,
+	bfin-gpio: GPIO 24 is already reserved by gpio-keys: BTN0, and you are
+configuring it as IRQ!
+
+        Note: Consider the case that, if there are two drivers need the
+	identical GPIO, one of them use it as GPIO, the other use it as
+	GPIO interrupt. This will really cause resource conflict. So if
+	there is any abnormal driver behavior, please check the bfin-gpio
+	warning messages.
+
+    - Kernel permit the identical GPIO be requested from the same driver twice.
+
+
+

arch/blackfin/Kconfig

@@ -26,6 +26,7 @@ config BLACKFIN
 	default y
 	select HAVE_IDE
 	select HAVE_OPROFILE
+	select ARCH_WANT_OPTIONAL_GPIOLIB
 
 config ZONE_DMA
 	bool
@@ -59,10 +60,6 @@ config GENERIC_CALIBRATE_DELAY
 	bool
 	default y
 
-config HARDWARE_PM
-	def_bool y
-	depends on OPROFILE
-
 source "init/Kconfig"
 
 source "kernel/Kconfig.preempt"
@@ -77,6 +74,26 @@ choice
 	prompt "CPU"
 	default BF533
 
+config BF512
+	bool "BF512"
+	help
+	  BF512 Processor Support.
+
+config BF514
+	bool "BF514"
+	help
+	  BF514 Processor Support.
+
+config BF516
+	bool "BF516"
+	help
+	  BF516 Processor Support.
+
+config BF518
+	bool "BF518"
+	help
+	  BF518 Processor Support.
+
 config BF522
 	bool "BF522"
 	help
@@ -137,6 +154,16 @@ config BF537
 	help
 	  BF537 Processor Support.
 
+config BF538
+	bool "BF538"
+	help
+	  BF538 Processor Support.
+
+config BF539
+	bool "BF539"
+	help
+	  BF539 Processor Support.
+
 config BF542
 	bool "BF542"
 	help
@@ -169,28 +196,55 @@ config BF561
 
 endchoice
 
+config SMP
+	depends on BF561
+	bool "Symmetric multi-processing support"
+	---help---
+	  This enables support for systems with more than one CPU,
+	  like the dual core BF561. If you have a system with only one
+	  CPU, say N. If you have a system with more than one CPU, say Y.
+
+	  If you don't know what to do here, say N.
+
+config NR_CPUS
+	int
+	depends on SMP
+	default 2 if BF561
+
+config IRQ_PER_CPU
+	bool
+	depends on SMP
+	default y
+
+config TICK_SOURCE_SYSTMR0
+	bool
+	select BFIN_GPTIMERS
+	depends on SMP
+	default y
+
 config BF_REV_MIN
 	int
-	default 0 if (BF52x || BF54x)
+	default 0 if (BF51x || BF52x || BF54x)
 	default 2 if (BF537 || BF536 || BF534)
 	default 3 if (BF561 ||BF533 || BF532 || BF531)
+	default 4 if (BF538 || BF539)
 
 config BF_REV_MAX
 	int
-	default 2 if (BF52x || BF54x)
+	default 2 if (BF51x || BF52x || BF54x)
 	default 3 if (BF537 || BF536 || BF534)
-	default 5 if (BF561)
+	default 5 if (BF561 || BF538 || BF539)
 	default 6 if (BF533 || BF532 || BF531)
 
 choice
 	prompt "Silicon Rev"
-	default BF_REV_0_1 if (BF52x || BF54x)
+	default BF_REV_0_1 if (BF51x || BF52x || BF54x)
 	default BF_REV_0_2 if (BF534 || BF536 || BF537)
 	default BF_REV_0_3 if (BF531 || BF532 || BF533 || BF561)
 
 config BF_REV_0_0
 	bool "0.0"
-	depends on (BF52x || BF54x)
+	depends on (BF51x || BF52x || BF54x)
 
 config BF_REV_0_1
 	bool "0.1"
@@ -206,11 +260,11 @@ config BF_REV_0_3
 
 config BF_REV_0_4
 	bool "0.4"
-	depends on (BF561 || BF533 || BF532 || BF531)
+	depends on (BF561 || BF533 || BF532 || BF531 || BF538 || BF539)
 
 config BF_REV_0_5
 	bool "0.5"
-	depends on (BF561 || BF533 || BF532 || BF531)
+	depends on (BF561 || BF533 || BF532 || BF531 || BF538 || BF539)
 
 config BF_REV_0_6
 	bool "0.6"
@@ -224,6 +278,11 @@ config BF_REV_NONE
 
 endchoice
 
+config BF51x
+	bool
+	depends on (BF512 || BF514 || BF516 || BF518)
+	default y
+
 config BF52x
 	bool
 	depends on (BF522 || BF523 || BF524 || BF525 || BF526 || BF527)
@@ -258,7 +317,7 @@ config MEM_MT48LC16M16A2TG_75
 
 config MEM_MT48LC32M8A2_75
 	bool
-	depends on (BFIN537_STAMP || PNAV10)
+	depends on (BFIN537_STAMP || PNAV10 || BFIN538_EZKIT)
 	default y
 
 config MEM_MT48LC8M32B2B5_7
@@ -271,10 +330,17 @@ config MEM_MT48LC32M16A2TG_75
 	depends on (BFIN527_EZKIT || BFIN532_IP0X || BLACKSTAMP || BFIN526_EZBRD)
 	default y
 
+config MEM_MT48LC32M8A2_75
+	bool
+	depends on (BFIN518F_EZBRD)
+	default y
+
+source "arch/blackfin/mach-bf518/Kconfig"
 source "arch/blackfin/mach-bf527/Kconfig"
 source "arch/blackfin/mach-bf533/Kconfig"
 source "arch/blackfin/mach-bf561/Kconfig"
 source "arch/blackfin/mach-bf537/Kconfig"
+source "arch/blackfin/mach-bf538/Kconfig"
 source "arch/blackfin/mach-bf548/Kconfig"
 
 menu "Board customizations"
@@ -307,6 +373,7 @@ config BOOT_LOAD
 
 config ROM_BASE
 	hex "Kernel ROM Base"
+	depends on ROMKERNEL
 	default "0x20040000"
 	range 0x20000000 0x20400000 if !(BF54x || BF561)
 	range 0x20000000 0x30000000 if (BF54x || BF561)
@@ -318,7 +385,7 @@ config CLKIN_HZ
 	int "Frequency of the crystal on the board in Hz"
 	default "11059200" if BFIN533_STAMP
 	default "27000000" if BFIN533_EZKIT
-	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD)
+	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN538_EZKIT || BFIN518F-EZBRD)
 	default "30000000" if BFIN561_EZKIT
 	default "24576000" if PNAV10
 	default "10000000" if BFIN532_IP0X
@@ -354,11 +421,11 @@ config VCO_MULT
 	range 1 64
 	default "22" if BFIN533_EZKIT
 	default "45" if BFIN533_STAMP
-	default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM)
+	default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM || BFIN538_EZKIT)
 	default "22" if BFIN533_BLUETECHNIX_CM
 	default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
 	default "20" if BFIN561_EZKIT
-	default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD)
+	default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD)
 	help
 	  This controls the frequency of the on-chip PLL. This can be between 1 and 64.
 	  PLL Frequency = (Crystal Frequency) * (this setting)
@@ -407,19 +474,70 @@ config MEM_MT46V32M16_5B
 	bool "MT46V32M16_5B"
 endchoice
 
-config MAX_MEM_SIZE
+choice
-	int "Max SDRAM Memory Size in MBytes"
+	prompt "DDR/SDRAM Timing"
-	depends on !MPU
+	depends on BFIN_KERNEL_CLOCK
-	default 512
+	default BFIN_KERNEL_CLOCK_MEMINIT_CALC
 	help
-	  This is the max memory size that the kernel will create CPLB
+	  This option allows you to specify Blackfin SDRAM/DDR Timing parameters
-	  tables for.  Your system will not be able to handle any more.
+	  The calculated SDRAM timing parameters may not be 100%
+	  accurate - This option is therefore marked experimental.
+
+config BFIN_KERNEL_CLOCK_MEMINIT_CALC
+	bool "Calculate Timings (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+
+config BFIN_KERNEL_CLOCK_MEMINIT_SPEC
+	bool "Provide accurate Timings based on target SCLK"
+	help
+	  Please consult the Blackfin Hardware Reference Manuals as well
+	  as the memory device datasheet.
+	  http://docs.blackfin.uclinux.org/doku.php?id=bfin:sdram
+endchoice
+
+menu "Memory Init Control"
+	depends on BFIN_KERNEL_CLOCK_MEMINIT_SPEC
+
+config MEM_DDRCTL0
+	depends on BF54x
+	hex "DDRCTL0"
+	default 0x0
+
+config MEM_DDRCTL1
+	depends on BF54x
+	hex "DDRCTL1"
+	default 0x0
+
+config MEM_DDRCTL2
+	depends on BF54x
+	hex "DDRCTL2"
+	default 0x0
+
+config MEM_EBIU_DDRQUE
+	depends on BF54x
+	hex "DDRQUE"
+	default 0x0
+
+config MEM_SDRRC
+	depends on !BF54x
+	hex "SDRRC"
+	default 0x0
+
+config MEM_SDGCTL
+	depends on !BF54x
+	hex "SDGCTL"
+	default 0x0
+endmenu
 
 #
 # Max & Min Speeds for various Chips
 #
 config MAX_VCO_HZ
 	int
+	default 400000000 if BF512
+	default 400000000 if BF514
+	default 400000000 if BF516
+	default 400000000 if BF518
 	default 600000000 if BF522
 	default 400000000 if BF523
 	default 400000000 if BF524
@@ -459,6 +577,7 @@ source kernel/Kconfig.hz
 
 config GENERIC_TIME
 	bool "Generic time"
+	depends on !SMP
 	default y
 
 config GENERIC_CLOCKEVENTS
@@ -533,6 +652,7 @@ endmenu
 
 
 menu "Blackfin Kernel Optimizations"
+	depends on !SMP
 
 comment "Memory Optimizations"
 
@@ -655,6 +775,17 @@ config APP_STACK_L1
 
 	  Currently only works with FLAT binaries.
 
+config EXCEPTION_L1_SCRATCH
+	bool "Locate exception stack in L1 Scratch Memory"
+	default n
+	depends on !APP_STACK_L1 && !SYSCALL_TAB_L1
+	help
+	  Whenever an exception occurs, use the L1 Scratch memory for
+	  stack storage.  You cannot place the stacks of FLAT binaries
+	  in L1 when using this option.
+
+	  If you don't use L1 Scratch, then you should say Y here.
+
 comment "Speed Optimizations"
 config BFIN_INS_LOWOVERHEAD
 	bool "ins[bwl] low overhead, higher interrupt latency"
@@ -684,7 +815,6 @@ config BFIN_INS_LOWOVERHEAD
 
 endmenu
 
-
 choice
 	prompt "Kernel executes from"
 	help
@@ -714,17 +844,9 @@ config BFIN_GPTIMERS
 	  To compile this driver as a module, choose M here: the module
 	  will be called gptimers.ko.
 
-config BFIN_DMA_5XX
-	bool "Enable DMA Support"
-	depends on (BF52x || BF53x || BF561 || BF54x)
-	default y
-	help
-	  DMA driver for BF5xx.
-
 choice
-	prompt "Uncached SDRAM region"
+	prompt "Uncached DMA region"
 	default DMA_UNCACHED_1M
-	depends on BFIN_DMA_5XX
 config DMA_UNCACHED_4M
 	bool "Enable 4M DMA region"
 config DMA_UNCACHED_2M
@@ -751,9 +873,11 @@ config BFIN_ICACHE_LOCK
 choice
 	prompt "Policy"
 	depends on BFIN_DCACHE
-	default BFIN_WB
+	default BFIN_WB if !SMP
+	default BFIN_WT if SMP
 config BFIN_WB
 	bool "Write back"
+	depends on !SMP
 	help
 	  Write Back Policy:
 	    Cached data will be written back to SDRAM only when needed.
@@ -790,7 +914,7 @@ endchoice
 
 config BFIN_L2_CACHEABLE
 	bool "Cache L2 SRAM"
-	depends on (BFIN_DCACHE || BFIN_ICACHE) && (BF54x || BF561)
+	depends on (BFIN_DCACHE || BFIN_ICACHE) && (BF54x || (BF561 && !SMP))
 	default n
 	help
 	  Select to make L2 SRAM cacheable in L1 data and instruction cache.
@@ -980,7 +1104,7 @@ config PM_WAKEUP_GPIO_NUMBER
 	int "GPIO number"
 	range 0 47
 	depends on PM_WAKEUP_BY_GPIO
-	default 2 if BFIN537_STAMP
+	default 2
 
 choice
 	prompt "GPIO Polarity"
@@ -1003,7 +1127,7 @@ comment "Possible Suspend Mem / Hibernate Wake-Up Sources"
 
 config PM_BFIN_WAKE_PH6
 	bool "Allow Wake-Up from on-chip PHY or PH6 GP"
-	depends on PM && (BF52x || BF534 || BF536 || BF537)
+	depends on PM && (BF51x || BF52x || BF534 || BF536 || BF537)
 	default n
 	help
 	  Enable PHY and PH6 GP Wake-Up (Voltage Regulator Power-Up)
@@ -1020,15 +1144,21 @@ menu "CPU Frequency scaling"
 
 source "drivers/cpufreq/Kconfig"
 
+config BFIN_CPU_FREQ
+	bool
+	depends on CPU_FREQ
+	select CPU_FREQ_TABLE
+	default y
+
 config CPU_VOLTAGE
 	bool "CPU Voltage scaling"
-	depends on EXPERIMENTAL	
+	depends on EXPERIMENTAL
 	depends on CPU_FREQ
 	default n
 	help
 	  Say Y here if you want CPU voltage scaling according to the CPU frequency.
 	  This option violates the PLL BYPASS recommendation in the Blackfin Processor
-	  manuals. There is a theoretical risk that during VDDINT transitions 
+	  manuals. There is a theoretical risk that during VDDINT transitions
 	  the PLL may unlock.
 
 endmenu

arch/blackfin/Kconfig.debug

@@ -2,8 +2,30 @@ menu "Kernel hacking"
 
 source "lib/Kconfig.debug"
 
+config DEBUG_STACKOVERFLOW
+	bool "Check for stack overflows"
+	depends on DEBUG_KERNEL
+	help
+	  This option will cause messages to be printed if free stack space
+	  drops below a certain limit.
+
+config DEBUG_STACK_USAGE
+	bool "Enable stack utilization instrumentation"
+	depends on DEBUG_KERNEL
+	help
+	  Enables the display of the minimum amount of free stack which each
+	  task has ever had available in the sysrq-T output.
+
+	  This option will slow down process creation somewhat.
+
 config HAVE_ARCH_KGDB
-       def_bool y
+	def_bool y
+
+config KGDB_TESTCASE
+	tristate "KGDB: for test case in expect"
+	default n
+	help
+	  This is a kgdb test case for automated testing.
 
 config DEBUG_VERBOSE
 	bool "Verbose fault messages"
@@ -182,11 +204,11 @@ config DEBUG_BFIN_HWTRACE_EXPAND_LEN
 	  4 for (2^4) 16k, or 4096 entries
 
 config DEBUG_BFIN_NO_KERN_HWTRACE
-	bool "Trace user apps (turn off hwtrace in kernel)"
+	bool "Turn off hwtrace in CPLB handlers"
 	depends on DEBUG_BFIN_HWTRACE_ON
-	default n
+	default y
 	help
-	  Some pieces of the kernel contain a lot of flow changes which can
+	  The CPLB error handler contains a lot of flow changes which can
 	  quickly fill up the hardware trace buffer.  When debugging crashes,
 	  the hardware trace may indicate that the problem lies in kernel
 	  space when in reality an application is buggy.

arch/blackfin/Makefile

@@ -21,6 +21,10 @@ KALLSYMS         += --symbol-prefix=_
 KBUILD_DEFCONFIG := BF537-STAMP_defconfig
 
 # setup the machine name and the machine dependent settings
+machine-$(CONFIG_BF512) := bf518
+machine-$(CONFIG_BF514) := bf518
+machine-$(CONFIG_BF516) := bf518
+machine-$(CONFIG_BF518) := bf518
 machine-$(CONFIG_BF522) := bf527
 machine-$(CONFIG_BF523) := bf527
 machine-$(CONFIG_BF524) := bf527
@@ -33,6 +37,8 @@ machine-$(CONFIG_BF533) := bf533
 machine-$(CONFIG_BF534) := bf537
 machine-$(CONFIG_BF536) := bf537
 machine-$(CONFIG_BF537) := bf537
+machine-$(CONFIG_BF538) := bf538
+machine-$(CONFIG_BF539) := bf538
 machine-$(CONFIG_BF542) := bf548
 machine-$(CONFIG_BF544) := bf548
 machine-$(CONFIG_BF547) := bf548
@@ -42,6 +48,10 @@ machine-$(CONFIG_BF561) := bf561
 MACHINE := $(machine-y)
 export MACHINE
 
+cpu-$(CONFIG_BF512) := bf512
+cpu-$(CONFIG_BF514) := bf514
+cpu-$(CONFIG_BF516) := bf516
+cpu-$(CONFIG_BF518) := bf518
 cpu-$(CONFIG_BF522) := bf522
 cpu-$(CONFIG_BF523) := bf523
 cpu-$(CONFIG_BF524) := bf524
@@ -54,6 +64,8 @@ cpu-$(CONFIG_BF533) := bf533
 cpu-$(CONFIG_BF534) := bf534
 cpu-$(CONFIG_BF536) := bf536
 cpu-$(CONFIG_BF537) := bf537
+cpu-$(CONFIG_BF538) := bf538
+cpu-$(CONFIG_BF539) := bf539
 cpu-$(CONFIG_BF542) := bf542
 cpu-$(CONFIG_BF544) := bf544
 cpu-$(CONFIG_BF547) := bf547
@@ -79,7 +91,7 @@ KBUILD_AFLAGS += -mcpu=$(cpu-y)-$(rev-y)
 CHECKFLAGS_SILICON = $(shell echo "" | $(CPP) $(KBUILD_CFLAGS) -dD - 2>/dev/null | awk '$$2 == "__SILICON_REVISION__" { print $$3 }')
 CHECKFLAGS += -D__SILICON_REVISION__=$(CHECKFLAGS_SILICON) -Dl1_text=__used__
 
-head-y   := arch/$(ARCH)/mach-$(MACHINE)/head.o arch/$(ARCH)/kernel/init_task.o
+head-y   := arch/$(ARCH)/kernel/init_task.o
 
 core-y   += arch/$(ARCH)/kernel/ arch/$(ARCH)/mm/ arch/$(ARCH)/mach-common/
 
@@ -95,10 +107,10 @@ else
 core-y	+= arch/$(ARCH)/kernel/cplb-nompu/
 endif
 
-libs-y   += arch/$(ARCH)/lib/
-
 drivers-$(CONFIG_OPROFILE) += arch/$(ARCH)/oprofile/
 
+libs-y   += arch/$(ARCH)/lib/
+
 machdirs	:= $(patsubst %,arch/blackfin/mach-%/, $(machine-y))
 
 KBUILD_CFLAGS += -Iarch/$(ARCH)/include/

arch/blackfin/configs/BlackStamp_defconfig

@@ -53,7 +53,7 @@ CONFIG_KALLSYMS=y
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
-CONFIG_ELF_CORE=y
+# CONFIG_ELF_CORE is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
@@ -276,7 +276,6 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_VIRT_TO_BUS=y
 CONFIG_BFIN_GPTIMERS=y
-CONFIG_BFIN_DMA_5XX=y
 # CONFIG_DMA_UNCACHED_4M is not set
 # CONFIG_DMA_UNCACHED_2M is not set
 CONFIG_DMA_UNCACHED_1M=y

arch/blackfin/configs/CM-BF527_defconfig

@@ -42,7 +42,7 @@ CONFIG_LOG_BUF_SHIFT=14
 CONFIG_FAIR_GROUP_SCHED=y
 CONFIG_FAIR_USER_SCHED=y
 # CONFIG_FAIR_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_SYSFS_DEPRECATED is not set
 # CONFIG_RELAY is not set
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_INITRAMFS_SOURCE=""
@@ -56,7 +56,7 @@ CONFIG_KALLSYMS=y
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
-CONFIG_ELF_CORE=y
+# CONFIG_ELF_CORE is not set
 CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
 CONFIG_ANON_INODES=y
@@ -190,14 +190,14 @@ CONFIG_IRQ_MAC_RX=11
 CONFIG_IRQ_PORTH_INTA=11
 CONFIG_IRQ_MAC_TX=11
 CONFIG_IRQ_PORTH_INTB=11
-CONFIG_IRQ_TMR0=12
+CONFIG_IRQ_TIMER0=12
-CONFIG_IRQ_TMR1=12
+CONFIG_IRQ_TIMER1=12
-CONFIG_IRQ_TMR2=12
+CONFIG_IRQ_TIMER2=12
-CONFIG_IRQ_TMR3=12
+CONFIG_IRQ_TIMER3=12
-CONFIG_IRQ_TMR4=12
+CONFIG_IRQ_TIMER4=12
-CONFIG_IRQ_TMR5=12
+CONFIG_IRQ_TIMER5=12
-CONFIG_IRQ_TMR6=12
+CONFIG_IRQ_TIMER6=12
-CONFIG_IRQ_TMR7=12
+CONFIG_IRQ_TIMER7=12
 CONFIG_IRQ_PORTG_INTA=12
 CONFIG_IRQ_PORTG_INTB=12
 CONFIG_IRQ_MEM_DMA0=13
@@ -292,7 +292,6 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_VIRT_TO_BUS=y
 CONFIG_BFIN_GPTIMERS=y
-CONFIG_BFIN_DMA_5XX=y
 # CONFIG_DMA_UNCACHED_4M is not set
 # CONFIG_DMA_UNCACHED_2M is not set
 CONFIG_DMA_UNCACHED_1M=y
@@ -650,6 +649,7 @@ CONFIG_BFIN_OTP=y
 # CONFIG_TWI_LCD is not set
 CONFIG_SIMPLE_GPIO=m
 # CONFIG_VT is not set
+# CONFIG_DEVKMEM is not set
 # CONFIG_SERIAL_NONSTANDARD is not set
 
 #
@@ -699,7 +699,7 @@ CONFIG_I2C_CHARDEV=m
 # I2C Hardware Bus support
 #
 CONFIG_I2C_BLACKFIN_TWI=m
-CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=50
+CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=100
 # CONFIG_I2C_GPIO is not set
 # CONFIG_I2C_OCORES is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set

arch/blackfin/configs/CM-BF533_defconfig

@@ -42,7 +42,7 @@ CONFIG_SYSVIPC_SYSCTL=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_SYSFS_DEPRECATED is not set
 # CONFIG_RELAY is not set
 # CONFIG_BLK_DEV_INITRD is not set
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
@@ -55,7 +55,7 @@ CONFIG_KALLSYMS=y
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 CONFIG_BUG=y
-CONFIG_ELF_CORE=y
+# CONFIG_ELF_CORE is not set
 CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
 CONFIG_ANON_INODES=y
@@ -254,7 +254,6 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_LARGE_ALLOCS=y
 # CONFIG_BFIN_GPTIMERS is not set
-CONFIG_BFIN_DMA_5XX=y
 # CONFIG_DMA_UNCACHED_2M is not set
 CONFIG_DMA_UNCACHED_1M=y
 # CONFIG_DMA_UNCACHED_NONE is not set
@@ -598,6 +597,7 @@ CONFIG_NETDEV_10000=y
 CONFIG_BFIN_SPORT=y
 # CONFIG_BFIN_TIMER_LATENCY is not set
 # CONFIG_VT is not set
+# CONFIG_DEVKMEM is not set
 # CONFIG_SERIAL_NONSTANDARD is not set
 
 #

arch/blackfin/configs/CM-BF537E_defconfig

@@ -42,7 +42,7 @@ CONFIG_SYSVIPC_SYSCTL=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_SYSFS_DEPRECATED is not set
 # CONFIG_RELAY is not set
 # CONFIG_BLK_DEV_INITRD is not set
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
@@ -55,7 +55,7 @@ CONFIG_KALLSYMS=y
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 CONFIG_BUG=y
-CONFIG_ELF_CORE=y
+# CONFIG_ELF_CORE is not set
 CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
 CONFIG_ANON_INODES=y
@@ -157,14 +157,14 @@ CONFIG_IRQ_UART1_RX=10
 CONFIG_IRQ_UART1_TX=10
 CONFIG_IRQ_MAC_RX=11
 CONFIG_IRQ_MAC_TX=11
-CONFIG_IRQ_TMR0=12
+CONFIG_IRQ_TIMER0=12
-CONFIG_IRQ_TMR1=12
+CONFIG_IRQ_TIMER1=12
-CONFIG_IRQ_TMR2=12
+CONFIG_IRQ_TIMER2=12
-CONFIG_IRQ_TMR3=12
+CONFIG_IRQ_TIMER3=12
-CONFIG_IRQ_TMR4=12
+CONFIG_IRQ_TIMER4=12
-CONFIG_IRQ_TMR5=12
+CONFIG_IRQ_TIMER5=12
-CONFIG_IRQ_TMR6=12
+CONFIG_IRQ_TIMER6=12
-CONFIG_IRQ_TMR7=12
+CONFIG_IRQ_TIMER7=12
 CONFIG_IRQ_PORTG_INTB=12
 CONFIG_IRQ_MEM_DMA0=13
 CONFIG_IRQ_MEM_DMA1=13
@@ -262,7 +262,6 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_LARGE_ALLOCS=y
 # CONFIG_BFIN_GPTIMERS is not set
-CONFIG_BFIN_DMA_5XX=y
 # CONFIG_DMA_UNCACHED_2M is not set
 CONFIG_DMA_UNCACHED_1M=y
 # CONFIG_DMA_UNCACHED_NONE is not set
@@ -627,6 +626,7 @@ CONFIG_NETDEV_10000=y
 CONFIG_BFIN_SPORT=y
 # CONFIG_BFIN_TIMER_LATENCY is not set
 # CONFIG_VT is not set
+# CONFIG_DEVKMEM is not set
 # CONFIG_SERIAL_NONSTANDARD is not set
 
 #

arch/blackfin/configs/CM-BF537U_defconfig

@@ -42,7 +42,7 @@ CONFIG_SYSVIPC_SYSCTL=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_SYSFS_DEPRECATED is not set
 # CONFIG_RELAY is not set
 # CONFIG_BLK_DEV_INITRD is not set
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
@@ -55,7 +55,7 @@ CONFIG_KALLSYMS=y
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 CONFIG_BUG=y
-CONFIG_ELF_CORE=y
+# CONFIG_ELF_CORE is not set
 CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
 CONFIG_ANON_INODES=y
@@ -157,14 +157,14 @@ CONFIG_IRQ_UART1_RX=10
 CONFIG_IRQ_UART1_TX=10
 CONFIG_IRQ_MAC_RX=11
 CONFIG_IRQ_MAC_TX=11
-CONFIG_IRQ_TMR0=12
+CONFIG_IRQ_TIMER0=12
-CONFIG_IRQ_TMR1=12
+CONFIG_IRQ_TIMER1=12
-CONFIG_IRQ_TMR2=12
+CONFIG_IRQ_TIMER2=12
-CONFIG_IRQ_TMR3=12
+CONFIG_IRQ_TIMER3=12
-CONFIG_IRQ_TMR4=12
+CONFIG_IRQ_TIMER4=12
-CONFIG_IRQ_TMR5=12
+CONFIG_IRQ_TIMER5=12
-CONFIG_IRQ_TMR6=12
+CONFIG_IRQ_TIMER6=12
-CONFIG_IRQ_TMR7=12
+CONFIG_IRQ_TIMER7=12
 CONFIG_IRQ_PORTG_INTB=12
 CONFIG_IRQ_MEM_DMA0=13
 CONFIG_IRQ_MEM_DMA1=13
@@ -262,7 +262,6 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_LARGE_ALLOCS=y
 # CONFIG_BFIN_GPTIMERS is not set
-CONFIG_BFIN_DMA_5XX=y
 # CONFIG_DMA_UNCACHED_2M is not set
 CONFIG_DMA_UNCACHED_1M=y
 # CONFIG_DMA_UNCACHED_NONE is not set
@@ -607,6 +606,7 @@ CONFIG_NETDEV_10000=y
 CONFIG_BFIN_SPORT=y
 # CONFIG_BFIN_TIMER_LATENCY is not set
 # CONFIG_VT is not set
+# CONFIG_DEVKMEM is not set
 # CONFIG_SERIAL_NONSTANDARD is not set
 
 #

arch/blackfin/configs/CM-BF548_defconfig

@@ -41,7 +41,7 @@ CONFIG_LOG_BUF_SHIFT=14
 CONFIG_FAIR_GROUP_SCHED=y
 CONFIG_FAIR_USER_SCHED=y
 # CONFIG_FAIR_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_SYSFS_DEPRECATED is not set
 # CONFIG_RELAY is not set
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_INITRAMFS_SOURCE=""
@@ -55,7 +55,7 @@ CONFIG_KALLSYMS=y
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
-CONFIG_ELF_CORE=y
+# CONFIG_ELF_CORE is not set
 CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
 CONFIG_ANON_INODES=y
@@ -325,7 +325,6 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_VIRT_TO_BUS=y
 # CONFIG_BFIN_GPTIMERS is not set
-CONFIG_BFIN_DMA_5XX=y
 # CONFIG_DMA_UNCACHED_2M is not set
 CONFIG_DMA_UNCACHED_1M=y
 # CONFIG_DMA_UNCACHED_NONE is not set
@@ -544,7 +543,7 @@ CONFIG_MTD_RAM=y
 CONFIG_MTD_COMPLEX_MAPPINGS=y
 CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_PHYSMAP_START=0x20000000
-CONFIG_MTD_PHYSMAP_LEN=0x800000
+CONFIG_MTD_PHYSMAP_LEN=0
 CONFIG_MTD_PHYSMAP_BANKWIDTH=2
 # CONFIG_MTD_UCLINUX is not set
 # CONFIG_MTD_PLATRAM is not set
@@ -732,6 +731,7 @@ CONFIG_BFIN_OTP=y
 # CONFIG_TWI_LCD is not set
 # CONFIG_SIMPLE_GPIO is not set
 # CONFIG_VT is not set
+# CONFIG_DEVKMEM is not set
 # CONFIG_SERIAL_NONSTANDARD is not set
 
 #
@@ -782,7 +782,7 @@ CONFIG_I2C_CHARDEV=y
 # I2C Hardware Bus support
 #
 CONFIG_I2C_BLACKFIN_TWI=y
-CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=50
+CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=100
 # CONFIG_I2C_GPIO is not set
 # CONFIG_I2C_OCORES is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set