Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC late changes from Arnd Bergmann:
 "These are changes that arrived a little late before the merge window
  or that have multiple dependencies on previous branches so they did
  not fit into one of the earlier ones.  There are 10 branches merged
  here, a total of 39 non-merge commits.  Contents are a mixed bag for
  the above reasons:

   * Two new SoC platforms: ST microelectronics stixxxx and the TI
     'Nspire' graphing calculator.  These should have been in the 'soc'
     branch but were a little late
   * Support for the Exynos 5420 variant in mach-exynos, which is based
     on the other exynos branches to avoid conflicts.
   * Various small changes for sh-mobile, ux500 and davinci
   * Common clk support for MSM"

* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
  ARM: ux500: bail out on alien cpus
  ARM: davinci: da850: adopt to pinctrl-single change for configuring multiple pins
  serial: sh-sci: Initialise variables before access in sci_set_termios()
  ARM: stih41x: Add B2020 board support
  ARM: stih41x: Add B2000 board support
  ARM: sti: Add DEBUG_LL console support
  ARM: sti: Add STiH416 SOC support
  ARM: sti: Add STiH415 SOC support
  ARM: msm: Migrate to common clock framework
  ARM: msm: Make proc_comm clock control into a platform driver
  ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
  ARM: msm: Remove clock-7x30.h include file
  ARM: msm: Remove custom clk_set_{max,min}_rate() API
  ARM: msm: Remove custom clk_set_flags() API
  msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
  msm: iommu: Convert to clk_prepare/unprepare
  msm_sdcc: Convert to clk_prepare/unprepare
  usb: otg: msm: Convert to clk_prepare/unprepare
  msm_serial: Use devm_clk_get() and properly return errors
  msm_serial: Convert to clk_prepare/unprepare
  ...

arch/arm/include/debug/nspire.S

@@ -0,0 +1,28 @@
+/*
+ *	linux/arch/arm/include/debug/nspire.S
+ *
+ *	Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#define NSPIRE_EARLY_UART_PHYS_BASE	   0x90020000
+#define NSPIRE_EARLY_UART_VIRT_BASE	   0xfee20000
+
+.macro	addruart, rp, rv, tmp
+	ldr \rp, =(NSPIRE_EARLY_UART_PHYS_BASE)		@ physical base address
+	ldr \rv, =(NSPIRE_EARLY_UART_VIRT_BASE)		@ virtual base address
+.endm
+
+
+#ifdef CONFIG_DEBUG_NSPIRE_CX_UART
+#include <asm/hardware/debug-pl01x.S>
+#endif
+
+#ifdef CONFIG_DEBUG_NSPIRE_CLASSIC_UART
+#define UART_SHIFT 2
+#include <asm/hardware/debug-8250.S>
+#endif

arch/arm/include/debug/sti.S

@@ -0,0 +1,61 @@
+/*
+ * arch/arm/include/debug/sti.S
+ *
+ * Debugging macro include header
+ * Copyright (C) 2013 STMicroelectronics (R&D) Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define STIH41X_COMMS_BASE              0xfed00000
+#define STIH41X_ASC2_BASE               (STIH41X_COMMS_BASE+0x32000)
+
+#define STIH41X_SBC_LPM_BASE            0xfe400000
+#define STIH41X_SBC_COMMS_BASE          (STIH41X_SBC_LPM_BASE + 0x100000)
+#define STIH41X_SBC_ASC1_BASE           (STIH41X_SBC_COMMS_BASE + 0x31000)
+
+
+#define VIRT_ADDRESS(x)		(x - 0x1000000)
+
+#if IS_ENABLED(CONFIG_STIH41X_DEBUG_ASC2)
+#define DEBUG_LL_UART_BASE	STIH41X_ASC2_BASE
+#endif
+
+#if IS_ENABLED(CONFIG_STIH41X_DEBUG_SBC_ASC1)
+#define DEBUG_LL_UART_BASE	STIH41X_SBC_ASC1_BASE
+#endif
+
+#ifndef DEBUG_LL_UART_BASE
+#error "DEBUG UART is not Configured"
+#endif
+
+#define ASC_TX_BUF_OFF  0x04
+#define ASC_CTRL_OFF    0x0c
+#define ASC_STA_OFF     0x14
+
+#define ASC_STA_TX_FULL         (1<<9)
+#define ASC_STA_TX_EMPTY        (1<<1)
+
+
+		.macro	addruart, rp, rv, tmp
+		ldr	\rp,      =DEBUG_LL_UART_BASE	@ physical base
+		ldr	\rv,      =VIRT_ADDRESS(DEBUG_LL_UART_BASE) @ virt base
+		.endm
+
+                .macro  senduart,rd,rx
+                strb    \rd, [\rx, #ASC_TX_BUF_OFF]
+                .endm
+
+                .macro  waituart,rd,rx
+1001:           ldr     \rd, [\rx, #ASC_STA_OFF]
+                tst     \rd, #ASC_STA_TX_FULL
+                bne     1001b
+                .endm
+
+                .macro  busyuart,rd,rx
+1001:           ldr     \rd, [\rx, #ASC_STA_OFF]
+                tst     \rd, #ASC_STA_TX_EMPTY
+                beq     1001b
+                .endm