Fully scripted conversion, see script in initial SPDX license commit
message.
tests/xfs/044 was hand massaged to remove duplicate copyright and
divider lines before running the script.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Previously _scratch_mount didn't check the mount status and most
tests continue to run even if the mount failed (unless test checks
for the mount status explicitly). This would result in running tests
on the underlying filesystem (usually rootfs) and implicit test
failures, and such failures can be annoying and are usually hard to
debug.
Now _fail test by default if _scratch_mount failed and introduce
_try_scratch_mount for tests that need to check mount results
themselves.
Suggested-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Eryu Guan <eguan@redhat.com>
So pass "-m crc=0" to the scratch_mkfs command so that we only run
on old v4 format filesystems where the UUID can be changed.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Some tests deliberately corrupt scratch devices and so will fail
the post-test check. Add a "_require_scratch_nocheck" helper
function for such tests to avoid false test failure detection.
Also, ensure that _notrun cleans up the trigger for the post-test
checks. Otherwise the next test to run may try to validate the
scratch/test devices even though they are not used by the test.
Further, _check_xfs_filesystem() causes check to exit if it finds a
corruption. This is extremely annoying as it terminates the entire
test run rather than just reporting that the test fails. Hence add
an "iam != check" test before exiting so that calls from tests will
cause the test to fail, but calls from check won't cause the harness
to exit.
There are still some tests that fail the scratch check, these are
not obvious test failures and so need further investigation to
determine the cause of the failures.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Currently we're checking file system consistency on TEST_DEV after every
successful test run even though the TEST_DEV might not even be used in
that test.
Fix it by introducing _require_test to for the test ti indicate that
it's about to use TEST_DEV.
Also add _require_test to the new script so that this requirement is a
default.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Introduce a top level common directory and move all the common.*
files into it. Because there is now a directory named common, the
prefix can be dropped from all the files. Convert all the tests to
use this new directory for including common files.
for f in common.*; do \
git mv `echo -n "$f " ; echo $f | sed -e 's;n\.;n/;'` \
done
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Phil White <pwhite@sgi.com>
[rjohnston@sgi.com reworked for TOT changes]
Signed-off-by: Rich Johnston <rjohnston@sgi.com>
Essentially the change is simply this. Converting:
... >> $seq.????
to:
.... >> $RESULT_DIR/$seq.????
so that output files are directed to the defined output directory.
sed to the rescue:
$ sed -i -e '/^seq=.*$/a seqres=$RESULT_DIR/$seq' -e 's/seq.full/seqres.full/' tests/*/*
will do most of the work automatically.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Phil White <pwhite@sgi.com>
[rjohnston@sgi.com reworked for TOT changes]
Signed-off-by: Rich Johnston <rjohnston@sgi.com>
Dave Chinner
Eryu Guan
Lukas Czerner
Rich Johnston